Waiting for device dev/disk/by-id/ata-...-part2 to appear

sudo vi /etc/fstab
sudo vi /boot/grub/menu.lst

sudo vi /etc/fstab

BEFORE
/dev/disk/by-id/ata-ST380013AS_4MR2NSD8-part1 swap                 swap       defaults             0 0
/dev/disk/by-id/ata-ST380013AS_4MR2NSD8-part2 /                    ext4       acl,user_xattr       1 1
/dev/disk/by-id/ata-ST380013AS_4MR2NSD8-part3 /home                ext4       acl,user_xattr       1 2
proc                 /proc                proc       defaults              0 0
sysfs                /sys                 sysfs      noauto                0 0
debugfs              /sys/kernel/debug    debugfs    noauto                0 0
usbfs                /proc/bus/usb        usbfs      noauto                0 0
devpts               /dev/pts             devpts     mode=0620,gid=5       0 0
 
AFTER
/dev/sda1 swap                 swap       defaults              0 0
/dev/sda2 /                    ext4       acl,user_xattr        1 1
/dev/sda3 /home                ext4       acl,user_xattr        1 2
proc                 /proc                proc       defaults              0 0
sysfs                /sys                 sysfs      noauto                0 0
debugfs              /sys/kernel/debug    debugfs    noauto                0 0
usbfs                /proc/bus/usb        usbfs      noauto                0 0
devpts               /dev/pts             devpts     mode=0620,gid=5       0 0

sudo vi /boot/grub/menu.lst

BEFORE
# Modified by YaST2. Last modification on Fri Nov 25 21:23:32 CET 2011
# THIS FILE WILL BE PARTIALLY OVERWRITTEN by perl-Bootloader
# For the new kernel it try to figure out old parameters. In case we are not able to recognize it (e.g. change of flavor or strange install order ) it it use as fallback installation parameters from /etc/sysconfig/bootloader


default 0
timeout 8
##YaST - generic_mbr
gfxmenu (hd0,1)/boot/message
##YaST - activate


###Don‘t change this comment - YaST2 identifier: Original name: linux###
title openSUSE 12.1 - 3.1.0-1.2
    root (hd0,1)
    kernel /boot/vmlinuz-3.1.0-1.2-default root=/dev/disk/by-id/ata-ST380013AS_4MR2NSD8-part2 resume=/dev/disk/by-id/ata-ST380013AS_4MR2NSD8-part1 splash=silent quiet showopts vga=0x31a
    initrd /boot/initrd-3.1.0-1.2-default


###Don‘t change this comment - YaST2 identifier: Original name: failsafe###
title Failsafe -- openSUSE 12.1 - 3.1.0-1.2
    root (hd0,1)
    kernel /boot/vmlinuz-3.1.0-1.2-default root=/dev/disk/by-id/ata-ST380013AS_4MR2NSD8-part2 showopts apm=off noresume nosmp maxcpus=0 edd=off powersaved=off nohz=off highres=off processor.max_cstate=1 nomodeset x11failsafe vga=0x31a
    initrd /boot/initrd-3.1.0-1.2-default

AFTER
# Modified by YaST2. Last modification on Fri Nov 25 21:23:32 CET 2011
# THIS FILE WILL BE PARTIALLY OVERWRITTEN by perl-Bootloader
# For the new kernel it try to figure out old parameters. In case we are not able to recognize it (e.g. change of flavor or strange install order ) it it use as fallback installation parameters from /etc/sysconfig/bootloader


default 0
timeout 8
##YaST - generic_mbr
gfxmenu (hd0,1)/boot/message
##YaST - activate


###Don‘t change this comment - YaST2 identifier: Original name: linux###
title openSUSE 12.1 - 3.1.0-1.2
    root (hd0,1)
    kernel /boot/vmlinuz-3.1.0-1.2-default root=/dev/sda2 resume=/dev/sda1 splash=silent quiet showopts vga=0x31a
    initrd /boot/initrd-3.1.0-1.2-default


###Don‘t change this comment - YaST2 identifier: Original name: failsafe###
title Failsafe -- openSUSE 12.1 - 3.1.0-1.2
    root (hd0,1)
    kernel /boot/vmlinuz-3.1.0-1.2-default root=/dev/sda2 showopts apm=off noresume nosmp maxcpus=0 edd=off powersaved=off nohz=off highres=off processor.max_cstate=1 nomodeset x11failsafe vga=0x31a
    initrd /boot/initrd-3.1.0-1.2-default