标签：int   when   any   close   dia   exiting   running   dos   removing   

"Installation failed !" in GUI but not in CLI (/usr/bin/winusb: line 78: 18265 Terminated )

Installation failed !
Exit code: 256
Log:
**blank**

-----

Install log(when running winusbgui as root)

Installation failed !
Exit code: 256
Log:
Formatting device...
Wait 3 seconds for block device nodes to populate...
mkfs.fat: warning - lowercase labels might not work properly with DOS or Windows
mkfs.fat 3.0.28 (2015-05-16)
Mounting...
mount: /dev/loop0 is write-protected, mounting read-only
Copying...
Installing grub...
Installing for i386-pc platform.
Installation finished. No error reported.
Installing grub.cfg...
Exiting...
Syncing...
/usr/local/bin/winusb: 行 78: 20260 終止                  while true; do
    sleep 0.05; echo ‘pulse‘;
done
Cleaning...
/usr/local/bin/winusb: 行 78: 20593 終止                  while true; do
    sleep 0.05; echo ‘pulse‘;
done
Unmounting and removing ‘/media/winusb_iso_1455346491_15903‘...
Unmounting and removing ‘/media/winusb_target_1455346491_15903‘...

P.S. "終止" in the output approximately means "terminated".

______________________________________________

Installation failed !
Exit code: 256
Log:
Formatting device...
Wait 3 seconds for block device nodes to populate...
mkfs.fat: warning - lowercase labels might not work properly with DOS or Windows
mkfs.fat 3.0.28 (2015-05-16)
Mounting...
Copying...
Installing grub...
Installing for i386-pc platform.
grub-install: warning: Attempting to install GRUB to a disk with multiple partition labels.  This is not supported yet..
grub-install: warning: 无法嵌入。在此次安装中 GRUB 只能通过使用块列表安装。但是块列表是不可信赖的，不推荐使用。.
Installation finished. No error reported.
Installing grub.cfg...
Exiting...
Syncing...
/usr/bin/winusb: 行 78:  7273 已终止               while true; do
    sleep 0.05; echo ‘pulse‘;
done
Cleaning...
/usr/bin/winusb: 行 78: 12165 已终止               while true; do
    sleep 0.05; echo ‘pulse‘;
done
Unmounting and removing ‘/media/winusb_iso_1482765713_2306‘...
Unmounting and removing ‘/media/winusb_target_1482765713_2306‘...

==================================

Do you have gksudo command installed on your system?

==================================

This issue is also reproduced in the following article:
Make A Bootable Windows 10 USB Install Stick On Linux With WinUSB Fork ~ Web Upd8: Ubuntu / Linux blog

====================================

I got same problem but solved now by
"sudo apt-get install gksu"
"gksudo winusbgui"
(i.e..type it without quotes)

Lin-Buo-Ren changed the title from "Installation failed !" in GUI but not in CLI to "Installation failed !" in GUI but not in CLI (/usr/bin/winusb: line 78: 18265 Terminated )

======================================================

Hi again, please use the latest revision in GitHub repo and see if it‘s still reproducible(it should be, as we never fixed the problem anyway).

=======================================================

I was encountered this issue right now, with windows 10.
I‘m on ubuntu 16.04 and WinUSB 1.0.11

I tried to run the installation anyway and it worked(I just ignored the error).

=====================================================

Hi, please use the latest revision in the repository (instead of latest released version) for reproducing the issue. We‘ve have changed a quite amount of code since 1.0.11

======================================================

I got similar problem and solve it!
I dont now why, but if you use GUI its not work. Use command line in way:
sudo winusb --format /path-to-ISO-file/filename.iso /dev/sdb (or other way to your flash)

=========================================================

The issue title already tell that CLI(command line interface) works.
This issue is about the GUI problem

"Installation failed !" in GUI but not in CLI (/usr/bin/winusb: line 78: 18265 Terminated )

标签：int   when   any   close   dia   exiting   running   dos   removing   

原文地址：http://www.cnblogs.com/sddai/p/6224401.html