4.2 接入交换机的相关配置
## 在此例中，我们联入的是一台接入交换机，此交换机的gi0/1口上联至核心交换机。也就意味着我们需要配置gi0/1为trunk口。具体的配置如下：
D-2960-3(config)#int gi0/1
D-2960-3(config-if)#sw
D-2960-3(config-if)#switchport mo
D-2960-3(config-if)#switchport mode ?
access Set trunking mode to ACCESS unconditionally
dynamic Set trunking mode to dynamically negotiate access or trunk mode
trunk Set trunking mode to TRUNK unconditionally
D-2960-3(config-if)#switchport mode trunk
## 配置此接口的模式为trunk，在cisoc2960交换机中，配置完接口模式为trunk后就可以了，不需要进一步配置此trunk口的封装状态，因为其默认的也是唯一的封装类型就是dot1q，并且此系列交换机并没有专门的封装配置命令。
D-2960-3(config-if)#exit
D-2960-3(config)#exit
D-2960-3#sh int tru # 退至特权配置模式验证一下刚才的配置
Port Mode Encapsulation Status Native vlan
Gi0/1 auto 802.1q trunking 1
# 这个端口已经配置成trunk模式，并且封装成802.1q了
Port Vlans allowed on trunk
Gi0/1 1-4094
Port Vlans allowed and active in management domain
Gi0/1 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160
Port Vlans in spanning tree forwarding state and not pruned
Gi0/1 1-2,10,20,30,40,50,60,70,80,100,110,120,150,160
D-2960-3#conf t # 进入到全局配置模式
D-2960-3(config)#vtp mode client
# 配置vtp模式为client，与核心交换机的server模式相呼应。
D-2960-3(config)#vtp domain pjoe
# 配置vtp域为pjoe，只有一个域中的交换机才能互传vlan信息。
D-2960-3(config)#vtp password pjoeserver # 配置vtp密码
D-2960-3(config)#end
D-2960-3#sh vtp status # 退出到特权模式验证一下刚才的有关vtp的配置
VTP Version : 2
Configuration Revision : 23
Maximum VLANs supported locally : 255
Number of existing VLANs : 19
VTP Operating Mode : Client # 模式已经设置成client
VTP Domain Name : pjoe # 域名已经设置成pjoe
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xEC 0x30 0xEF 0x6F 0xA5 0x9A 0x39 0x7B
# 密码已经配置完毕，但是被加密显示了
Configuration last modified by 192.168.113.254 at 12-3-07 22:58:54
##稍等一会后，验证一下是否学习到了核心交换机的vlan信息，它的学习有一小段的过程30秒的样子。
D-2960-3#sh vlan # 验证一下vlan信息是否全部学到。
VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4, Fa0/5, Fa0/6, Fa0/7, Fa0/8, Fa0/9, Fa0/10, Fa0/11,Fa0/12, Fa0/13, Fa0/14, Fa0/15, Fa0/16, Fa0/17, Fa0/18, Fa0/19, Fa0/20, Fa0/21,Fa0/22, Fa0/23, Fa0/24, Fa0/25, Fa0/26, Fa0/27, Fa0/28, Fa0/29, Fa0/30, Fa0/31,Fa0/32, Fa0/33, Fa0/34, Fa0/35, Fa0/36, Fa0/37, Fa0/38, Fa0/39, Fa0/40, Fa0/41,a0/42, Fa0/43, Fa0/44, Fa0/45, Fa0/46, Fa0/47, Fa0/48, Gi0/2 2 firewall active # ok，核心交换机上配置好的vlan信息已经被这台交换机学习到了，剩下的工作仅需要将相应的端口添加到相应的vlan中就可以了，此处不赘述。 10 Engineering active 20 Procurement active 30 QAQC active 40 Operation active 50 Yard active 60 BM active 70 HRAD active 80 Facility active 100 Finance active 110 GO active 120 Wlan active 150 Server active 160 Client active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 2 enet 100002 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 30 enet 100030 1500 - - - - - 0 0 40 enet 100040 1500 - - - - - 0 0 50 enet 100050 1500 - - - - - 0 0 60 enet 100060 1500 - - - - - 0 0 70 enet 100070 1500 - - - - - 0 0 80 enet 100080 1500 - - - - - 0 0 100 enet 100100 1500 - - - - - 0 0 110 enet 100110 1500 - - - - - 0 0 120 enet 100120 1500 - - - - - 0 0 150 enet 100150 1500 - - - - - 0 0 160 enet 100160 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0
D-2960-3#
# 配置这台交换机的管理IP
D-2960-3(config)#int vlan 1 # 管理ip地址我们配置在vlan1上
D-2960-3(config-if)#ip address 192.168.113.222 255.255.255.0 # 设置实际的ip地址
D-2960-3(config-if)#exit
D-2960-3(config)#ip default-gateway 192.168.113.254
# 设置这台交换机的网关，此地址即为核心交换机vlan1的地址。
D-2960-3(config)#end
D-2960-3#sh run # 验证一下完整的配置。
Building configuration... Current configuration : 2087 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname D-2960-3 ! enable password 7 12090F18170805172924 ! no aaa new-model system mtu routing 1500 ip subnet-zero ! no file verify auto spanning-tree mode pvst spanning-tree extend system-id ! vlan internal allocation policy ascending ! interface FastEthernet0/1 ! interface FastEthernet0/2 ! interface FastEthernet0/3 ! (省略… …) interface FastEthernet0/45 ! interface FastEthernet0/46 ! interface FastEthernet0/47 ! interface FastEthernet0/48 ! interface GigabitEthernet0/1 ! interface GigabitEthernet0/2 ! interface Vlan1 ip address 192.168.113.222 255.255.255.0 no ip route-cache ! ip default-gateway 192.168.113.254 ip http server ! control-plane ! ! line con 0 password 7 12090F18170805172924 line vty 0 4 password 7 12090F18170805172924 login line vty 5 15 login ! end
D-2960-3#
