码迷,mamicode.com
首页 > 系统相关 > 详细

Linux网络管理

时间:2018-01-22 11:58:00      阅读:222      评论:0      收藏:0      [点我收藏+]

标签:uid   scope   code   pack   标签   secondary   bootproto   only   uuid   

一、Linux网络配置方式

Linux网络配置有两种方式, 如下:

  • 静态指定:
    • 命令: ifconfig, route, ip, ss, ...
    • 配置文件
    • 图形工具: CentOS 6(system-config-network-tui, setup); CentOS 7(nmtui)
  • 动态分配: DHCP(Dynamic Host Configuration Protocol)

二、网路配置命令

2.1 ifconfig命令

用法1: ifconfig [interface]

# ifconfig [-a]: 显示所有网络接口详细信息, 不加“-a”也可以
[root@zabbix ~]# ifconfig 
docker0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 172.17.0.1  netmask 255.255.0.0  broadcast 0.0.0.0
        ether 02:42:84:6c:65:e2  txqueuelen 0  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

eno16777736: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.123.132  netmask 255.255.255.0  broadcast 192.168.123.255
        inet6 fe80::20c:29ff:fe7b:f986  prefixlen 64  scopeid 0x20<link>
        ether 00:0c:29:7b:f9:86  txqueuelen 1000  (Ethernet)
        RX packets 225  bytes 25331 (24.7 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 254  bytes 82633 (80.6 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 12028  bytes 2818167 (2.6 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 12028  bytes 2818167 (2.6 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

# ifconfig IFACE: 显示指定网络接口详细信息
[root@zabbix ~]# ifconfig docker0
docker0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 172.17.0.1  netmask 255.255.0.0  broadcast 0.0.0.0
        ether 02:42:84:6c:65:e2  txqueuelen 0  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

用法2: ifconfig interface [aftype] options | address ...

# ifconfig IFACE ip[/mask] [up]: 设置一个网络接口, up(默认)为启用;
# ifconfig IFACE IP netmask MASK [up]: 同上
[root@zabbix ~]# ifconfig eno16777736:0 192.168.123.133 up
[root@zabbix ~]# ifconfig eno16777736:0
eno16777736:0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.123.133  netmask 255.255.255.0  broadcast 192.168.123.255
        ether 00:0c:29:7b:f9:86  txqueuelen 1000  (Ethernet)

Note: 以上配置方式为立即生效.

2.2 route命令

route命令用于进行路由管理.

查看当前内核路由表

用法: route -n

[root@zabbix ~]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG    100    0        0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
172.29.2.0      192.168.123.2   255.255.255.0   UG    100    0        0 eno16777736
192.168.123.0   0.0.0.0         255.255.255.0   U     100    0        0 eno16777736

添加路由

用法: route add [-net|-host] target [netmask Nm] [gw GW] [[dev] IFACE]

# 添加一条主机路由 目标为172.29.2.43, 网关为192.168.123.2;
[root@zabbix ~]# route add -host 172.29.2.43 gw 192.168.123.2 dev eno16777736
[root@zabbix ~]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG    100    0        0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
172.29.2.43     192.168.123.2   255.255.255.255 UGH   0      0        0 eno16777736
192.168.123.0   0.0.0.0         255.255.255.0   U     100    0        0 eno16777736

# 添加一条网络路由, 目标为172.29.0.0; 网关为192.168.123.2
root@zabbix ~]# route add -net 172.29.0.0 netmask 255.255.0.0 gw 192.168.123.2 dev eno16777736
[root@zabbix ~]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG    100    0        0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
172.29.0.0      192.168.123.2   255.255.0.0     UG    0      0        0 eno16777736
172.29.2.43     192.168.123.2   255.255.255.255 UGH   0      0        0 eno16777736
192.168.123.0   0.0.0.0         255.255.255.0   U     100    0        0 eno16777736

# 添加一条默认路由, 网关为192.168.123.2; 以下两种方式都可以.
[root@zabbix ~]# route add -net 0.0.0.0 netmask 0.0.0.0 gw 192.168.123.2
[root@zabbix ~]# route add default gw 192.168.123.2

删除路由

用法: route del [-net|-host] target [netmask Nm] [gw GW] [[dev] IFACE]

# 删除一条主机路由
[root@zabbix ~]# route del -host 172.29.2.43
[root@zabbix ~]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG    100    0        0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
172.29.0.0      192.168.123.2   255.255.0.0     UG    0      0        0 eno16777736
192.168.123.0   0.0.0.0         255.255.255.0   U     100    0        0 eno16777736

# 删除一条网络路由
[root@zabbix ~]# route del -net 172.29.0.0 netmask 255.255.0.0
[root@zabbix ~]# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG    100    0        0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U     0      0        0 docker0
192.168.123.0   0.0.0.0         255.255.255.0   U     100    0        0 eno16777736

Note: 使用命令的方式配置的路由条目会立即生效, 但不会永久有效, 当重启网卡或者重启主机就会失效.

2.3 DNS解析命令

DNS配置文件: /etc/resolv.conf

nameserver DNS_SERVER_IP1
nameserver DNS_SERVER_IP2
nameserver DNS_SERVER_IP3

dns正向解析: FQDN(Fully Qualified Domain Name, 完全限定域名) --> IP

# dig -t A FQDN
# host -t A FQDN

dns反向解析: IP --> FQDN

# dig -x IP
# host -t PTR IP

2.4 网络连接查看命令 - netstat

netstat用于显示网络连接状态, 内核路由表, 接口统计, 伪装连接和组播成员.

显示网络连接

用法: netstat [--tcp|-t] [--udp|-u] [--raw|-w] [--listening|-l] [--all|-a] [--numeric|-n] [--extend|-e[--extend|-e] [--program|-p]

# -t: tcp协议相关
# -u: udp协议相关
# -r: raw socket相关
# -l: 处于监听状态
# -a: 所有状态
# -n: 以数字显示IP和端口
# -e: 扩展格式
# -p: 显示相关进程及PID

# 以数字格式显示所有tcp相关连接
[root@zabbix ~]# netstat -tan
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State      
tcp        0      0 0.0.0.0:3306            0.0.0.0:*               LISTEN     
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN     
tcp        0      0 127.0.0.1:25            0.0.0.0:*               LISTEN     
...

# 以数字格式显示所有udp相关连接
[root@zabbix ~]# netstat -uan
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State      
udp        0      0 0.0.0.0:6842            0.0.0.0:*                          
udp        0      0 0.0.0.0:68              0.0.0.0:*                          
udp        0      0 127.0.0.1:323           0.0.0.0:*                          
udp6       0      0 ::1:323                 :::*                               
udp6       0      0 :::34427                :::*                       

# 以数字格式显示所有处于监听状态的tcp连接
[root@zabbix ~]# netstat -tnl
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State      
tcp        0      0 0.0.0.0:3306            0.0.0.0:*               LISTEN     
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN     
tcp        0      0 127.0.0.1:25            0.0.0.0:*               LISTEN     
tcp        0      0 0.0.0.0:10050           0.0.0.0:*               LISTEN     
tcp        0      0 0.0.0.0:10051           0.0.0.0:*               LISTEN     
tcp6       0      0 :::80                   :::*                    LISTEN     
tcp6       0      0 :::22                   :::*                    LISTEN     
tcp6       0      0 ::1:25                  :::*                    LISTEN     
tcp6       0      0 :::10050                :::*                    LISTEN     
tcp6       0      0 :::10051                :::*                    LISTEN     

# 以数字格式显示所有处于监听状态udp连接: netstat -unl

# 以数字格式显示所有处于监听状态的tcp连接, 并显示相关进程及pid: netstat -tnlp

# 以数字格式显示所有出去监听状态的udp连接, 并显示相关进程和pid: netstat -unlp

显示内核路由表

用法: netstat {--route|-r} [--extend|-e[--extend|-e]] [--verbose|-v] [--numeric|-n]

# -r: 显示内核路由表
[root@zabbix ~]# netstat -r
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
default         gateway         0.0.0.0         UG        0 0          0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U         0 0          0 docker0
172.29.2.0      gateway         255.255.255.0   UG        0 0          0 eno16777736
192.168.123.0   0.0.0.0         255.255.255.0   U         0 0          0 eno16777736

# -n: 以数字格式显示
[root@zabbix ~]# netstat -rn
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG        0 0          0 eno16777736
172.17.0.0      0.0.0.0         255.255.0.0     U         0 0          0 docker0
172.29.2.0      192.168.123.2   255.255.255.0   UG        0 0          0 eno16777736
192.168.123.0   0.0.0.0         255.255.255.0   U         0 0          0 eno16777736

接口统计数据

用法: netstat {--interfaces|-I|-i} [--all|-a] [--extend|-e] [--program|-p] [--numeric|-n]

# -I<IFACE>: 显示指定接口
[root@zabbix ~]# netstat -Idocker0
Kernel Interface table
Iface      MTU    RX-OK RX-ERR RX-DRP RX-OVR    TX-OK TX-ERR TX-DRP TX-OVR Flg
docker0   1500        0      0      0 0             0      0      0      0 BMU

# -i: 显示所有网络接口
[root@zabbix ~]# netstat -i
Kernel Interface table
Iface      MTU    RX-OK RX-ERR RX-DRP RX-OVR    TX-OK TX-ERR TX-DRP TX-OVR Flg
docker0   1500        0      0      0 0             0      0      0      0 BMU
eno16777  1500    21658      0      0 0          4968      0      0      0 BMRU
lo       65536   130925      0      0 0        130925      0      0      0 LRU

2.5 路由信息(包括策略路由)、网络设备和ip隧道管理命令 - ip

用法: ip [ OPTIONS ] OBJECT { COMMAND | help }

OBJECT: { link | addr | route }
OPTIONS: { -V[ersion] | -s[tatistics] | -r[esolve] | -f[amily] { inet | inet6 | ipx | dnet | link } | -o[neline] | -n[etns] name }

网络接口信息查看

用法: ip link show

# 显示所有接口信息: ip link show
[root@zabbix ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno16777736: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000
    link/ether 00:0c:29:7b:f9:86 brd ff:ff:ff:ff:ff:ff
3: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT 
    link/ether 02:42:48:10:bd:c5 brd ff:ff:ff:ff:ff:ff

# 查看指定接口新: ip link show dev IFACE
[root@zabbix ~]# ip link show dev docker0
3: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT 
    link/ether 02:42:48:10:bd:c5 brd ff:ff:ff:ff:ff:ff

# 查看所有已激活接口的信息: ip link show up
[root@zabbix ~]# ip link show up
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno16777736: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000
    link/ether 00:0c:29:7b:f9:86 brd ff:ff:ff:ff:ff:ff
3: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT 
    link/ether 02:42:48:10:bd:c5 brd ff:ff:ff:ff:ff:ff

网络接口状态设置

用法: ip link set

# 激活或禁用某个接口: ip link set dev IFACE up|down
[root@zabbix ~]# ip link set dev docker0 down
[root@zabbix ~]# ip link show up
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno16777736: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000
    link/ether 00:0c:29:7b:f9:86 brd ff:ff:ff:ff:ff:ff

ip地址管理

用法: ip addr

# ip地址的添加或移除: ip addr <add|del> IP_ADDRESS/MASK dev IFACE
    # [label ‘LABEL‘]: 添加地址时指明网卡标签
    # [scope {global|link|host}]: 指明作用域
        # global: 全局有效
        # link: 仅链接有用
        # host: 仅本机可用
    # [broadcast ADDRESS]: 指明广播域
# 添加一个新地址
[root@zabbix ~]# ip addr add 192.168.123.101/24 dev eno16777736:0
[root@zabbix ~]# ip addr show eno16777736
2: eno16777736: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 00:0c:29:7b:f9:86 brd ff:ff:ff:ff:ff:ff
    inet 192.168.123.132/24 brd 192.168.123.255 scope global dynamic eno16777736
       valid_lft 1685sec preferred_lft 1685sec
    inet 192.168.123.101/24 scope global secondary eno16777736 # 新添加的地址
       valid_lft forever preferred_lft forever
    inet6 fe80::20c:29ff:fe7b:f986/64 scope link 
       valid_lft forever preferred_lft forever

# 移除
[root@zabbix ~]# ip addr del 192.168.123.101/24 dev eno16777736:0 # 删除
[root@zabbix ~]# ip addr show dev eno16777736
2: eno16777736: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:0c:29:7b:f9:86 brd ff:ff:ff:ff:ff:ff
inet 192.168.123.132/24 brd 192.168.123.255 scope global dynamic eno16777736
   valid_lft 1486sec preferred_lft 1486sec
inet6 fe80::20c:29ff:fe7b:f986/64 scope link 
   valid_lft forever preferred_lft forever

# 指定一个标签
[root@zabbix ~]# ip addr add 192.168.123.100/24 dev eno16777736 label ‘eno16777736:0‘
[root@zabbix ~]# ifconfig eno16777736:0
eno16777736:0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
    inet 192.168.123.100  netmask 255.255.255.0  broadcast 0.0.0.0
    ether 00:0c:29:7b:f9:86  txqueuelen 1000  (Ethernet)

[root@zabbix ~]# ip addr del 192.168.123.100/24 dev eno16777736 label ‘eno16777736:0‘

# 查询协议地址: ip add show
    # [dev IFACE]
    # [label ‘LABEL‘]
    # [primary and secondary]
[root@zabbix ~]# ip add show dev docker0
3: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN 
    link/ether 02:42:91:38:6b:00 brd ff:ff:ff:ff:ff:ff
    inet 172.17.0.1/16 scope global docker0
       valid_lft forever preferred_lft forever

# 清空协议地址: ip add flush
[root@zabbix ~]# ip addr flush dev eno16777736 label ‘eno16777736:0‘

路由管理

# 添加路由: ip route add TARGET via GW dev IFACE [src SOURCE_IP]
    # 主机路由: IP
    # 网络路由: IP/MASK
[root@zabbix ~]# ip route add to 172.29.2.43 via  192.168.123.2 dev eno16777736 # 主机路由不用指定掩码, 默认为32
[root@zabbix ~]# ip route add 172.29.0.0/16 via 192.168.123.2
[root@zabbix ~]# ip route add default via 192.168.123.2 # 添加默认网关

# 显示内核路由表: ip route show
[root@zabbix ~]# ip route show
default via 192.168.123.2 dev eno16777736  proto static  metric 100 
172.17.0.0/16 dev docker0  proto kernel  scope link  src 172.17.0.1 
172.29.0.0/16 via 192.168.123.2 dev eno16777736 
172.29.2.43 via 192.168.123.2 dev eno16777736 
192.168.123.0/24 dev eno16777736  proto kernel  scope link  src 192.168.123.132  metric 100

#删除路由: ip route del TARGET
[root@zabbix ~]# ip route del 172.29.2.43
[root@zabbix ~]# ip route del 172.29.0.0/16
[root@zabbix ~]# ip route del default
[root@zabbix ~]# ip route show
default via 192.168.123.2 dev eno16777736  proto static  metric 100 
172.17.0.0/16 dev docker0  proto kernel  scope link  src 172.17.0.1 
192.168.123.0/24 dev eno16777736  proto kernel  scope link  src 192.168.123.132  metric 100 

# 清空路由表: ip route flush
    # [dev IFACE]
    # [via PREFIX]
[root@zabbix ~]# ip route flush dev eno16777736
[root@zabbix ~]# ip route show
172.17.0.0/16 dev docker0 proto kernel scope link src 172.17.0.1

Note: 以上方式添加或删除的路由立即生效, 重启系统或者network服务后失效.

2.6 网络套接字接口查看工具

用法: ss [options] [FILTER]

# [options]:
    # -t: tcp协议相关
    # -u: udp协议相关
    # -w: 裸套接字相关
    # -x: unix sock相关
    # -l: listen状态的连接
    # -a: 所有状态
    # -n: 数字格式
    # -p: 相关的程序及pid
    # -e: 扩展的信息
    # -m: 内存用量
    # -o: 计时器信息

# [FILTER]:
    # FILETER: [state TCP-STATE] [EXPRESSION]
        # TCP-STATE: established, syn-sent, syn-recv, fin-wait-1, fin-wait-2, time-wait, closed, close-wait, last-ack, listen and closing.
        # EXPRESSION: dport =; sport =; 示例: ‘( dport = :ssh or sport = :ssh )‘

# 以数字格式显示所有tcp相关连接: ss -tan
[root@zabbix ~]# ss -tan
State      Recv-Q Send-Q                  Local Address:Port                                 Peer Address:Port              
LISTEN     0      50                                  *:3306                                            *:*                  
LISTEN     0      128                                 *:22                                              *:*                  
LISTEN     0      100                         127.0.0.1:25                                              *:*                  
LISTEN     0      128                                 *:10050                                           *:*                  
LISTEN     0      128                                 *:10051                                           *:*                  
ESTAB      0      0                     192.168.123.132:46052                             192.168.123.132:3306               
...

# 常用组合: -tan, -tanl, =tanlp, -uan

# 通过FILTER过滤
[root@zabbix ~]# ss -tan state established ‘( sport = 3306 )‘ 
Recv-Q Send-Q                            Local Address:Port                                           Peer Address:Port              
0      0                               192.168.123.132:3306                                        192.168.123.132:40527              
0      0                               192.168.123.132:3306                                        192.168.123.132:40526              
0      0                               192.168.123.132:3306                                        192.168.123.132:40539              
0      0                               192.168.123.132:3306                                        192.168.123.132:40528              
0      0                               192.168.123.132:3306                                        192.168.123.132:40537              
0      0                               192.168.123.132:3306                                        192.168.123.132:40545              
0      0                               192.168.123.132:3306                                        192.168.123.132:40533              
0      0                               192.168.123.132:3306                                        192.168.123.132:40538              
0      0                               192.168.123.132:3306                                        192.168.123.132:40534              
0      0                               192.168.123.132:3306                                        192.168.123.132:40531              
0      0                               192.168.123.132:3306                                        192.168.123.132:40541              
0      0                               192.168.123.132:3306                                        192.168.123.132:40530              
0      0                               192.168.123.132:3306                                        192.168.123.132:40529              
0      0                               192.168.123.132:3306                                        192.168.123.132:40544              
0      0                               192.168.123.132:3306                                        192.168.123.132:40542              
0      0                               192.168.123.132:3306                                        192.168.123.132:40535              
0      0                               192.168.123.132:3306                                        192.168.123.132:40543              
0      0                               192.168.123.132:3306                                        192.168.123.132:40540              
0      0                               192.168.123.132:3306                                        192.168.123.132:40546              
0      0                               192.168.123.132:3306                                        192.168.123.132:40532              
0      0                               192.168.123.132:3306                                        192.168.123.132:40536              
0      0                               192.168.123.132:3306                                        192.168.123.132:40596              
0      0                               192.168.123.132:3306                                        192.168.123.132:40547

2.7 修改网络配置文件

IP, MASK, GW, DNS相关配置文件: /etc/sysconfig/network-scripts/ifcfg-IFACE

DEVICE="IFACE": 此配置文件应用到的设备
HWADDR="MAC_ADDRESS": 对应设备的mac地址
BOOTPROTO=="static|dhcp|none|bootp": 激活此设备时使用的地址配置协议
NM_CONTROLLED="yes|no": NM是NetworkManager的简写, 此网卡是否接受NM控制, CentOS简写为“no”
ONBOOT="yes|no": 在系统引导时是否激活此设备
TYPE="Ethernet|Bridge": 接口类型
UUID="uuid": 设备的唯一标识
IPADDR="IP_ADDRESS": 指明IP地址
NETMASK="MASK": 子网掩码
GATEWAY="gateway": 默认网关
DNS1="DNS_SERVER_IP1": 第一个DNS服务器
DNS2="DNS_SERVER_IP2":
DNS3="DNS_SERVER_IP3":
USERCTL="yes|no": 普通用户是否可控制此设备
PEERDNS="yes|no": 如果BOOTPROTO的值为“dhcp”, 是否允许dhcp server分配的dns服务器指向信息直接覆盖至/etc/resolv.conf文件中

Note: 通过网络配置文件给网卡配置多地址, ifcfg-IFACE_ALIAS中DEVICE="IFACE_ALIAS", 网卡别名不用使用DHCP引导.

路由相关配置文件: /etc/sysconfig/network-scripts/route-IFACE

# 两种方式:
# 1. TARGET via GW
[root@zabbix network-scripts]# vim route-eno16777736
172.29.0.0/16 via 192.168.123.2

2. 每三行定义一条路由
# ADDRESS#(#号表示数字, 表示第几组路由)=TARGET
# NETMASK#=mask
# GATEWAY#=GW
[root@zabbix network-scripts]# vim route-eno16777736 
ADDRESS0=172.29.2.0
NETMASK0=255.255.255.0
GATEWAY0=192.168.123.2

Linux网络管理

标签:uid   scope   code   pack   标签   secondary   bootproto   only   uuid   

原文地址:http://blog.51cto.com/13501622/2063581

(0)
(0)
   
举报
评论 一句话评论(0
登录后才能评论!
© 2014 mamicode.com 版权所有  联系我们:gaon5@hotmail.com
迷上了代码!