标签：style blog http tar com width
Creating an IP Tunnel using GRE on Linux
| Contents[hide] |
We will do IPv4 tunneling using GRE. GRE is a tunneling protocol that was originally developed by Cisco, and it can do a few more things than IP-in-IP tunneling. For example, you can also transport multicast traffic and IPv6 through a GRE tunnel.
We are using Debian with linux kernel 2.4.26. In Linux, you‘ll need the ip_gre.o module.
We have 2 routers X and Y, and intermediate network C (or let‘s say, Internet).
router X
Router X is connected to the Internet on interface eth0 and network A on eth1.
interface eth0 :: address 169.229.255.134 on the Internet (or network C)
interface eth1 :: address 10.0.2.1, network 10.0.2.0/24 (network A)
router Y
Router Y is connected to the Internet on interface eth0, network B on eth1 and network C on eth2.
interface eth0 :: address 207.241.237.37 on the Internet (or network C)
interface eth1 :: address 10.0.3.1, network 10.0.3.0/24 (network B)
interface eth2 :: address 10.0.4.1, network 10.0.4.0/24 (network C)
As far as network C is concerned, we assume that it will pass any packet sent from X to Y and vice versa. How and why, we do not care.
Create a tunnel between router X and Y, such that we can route traffic from network A (connected to X) to networks B and C (connected to Y). This tunnel will look just like a wire between the two routers with its own subnet (10.0.201.0/24)
On router X, commands are
iptunnel add tunX mode gre remote 207.241.237.37 local 169.229.255.134 ttl 225
ifconfig tunX 10.0.201.1/24
ifconfig tunX up
ifconfig tunX pointopoint 10.0.201.2
ifconfig tunX multicast
In line 1, we added a tunnel device, and called it tunX. Furthermore we told it to use the GRE protocol (mode gre), that the remote address is 207.241.237.37 (the router Y at the other end), that our tunneling packets should originate from 169.229.255.134 (which allows your router to have several interfaces and choose which one to use for tunneling) and that the TTL field of the packet should be set to 255 (ttl 255).
Line 2 gives the newly born interface tunY the address 10.0.201.1.
Line 3 enables the device.
Line 4 is necessary to set the IP address of the peer. Need when using dynamic routing with RIP/OSPF with Zebra. Refer to Routing HOWTO for more details.
Line 5 is necessary to enable multicast - so that routing with Zebra works (they normally multicast routing updates).
One router Y, commands are
iptunnel add tunY mode gre local 207.241.237.37 remote 169.229.255.134 ttl 225
ifconfig tunY 10.0.201.2/24
ifconfig tunY up
ifconfig tunY pointopoint 10.0.201.1
ifconfig tunY multicast
Tunnel X<->Y Now we created a tunnel on the 10.0.201.0/24 network from router X to Y and vice versa.
routerX ----------------tunnel-----------------routerY
10.0.201.1 10.0.201.2
(tunX) (tunY)
We can send packets on the 10.0.201.0/24 network from router X to Y and vice versa. So we can ping router X from Y on the tunnel interface.
routerX# ping 10.0.201.2
routerY# ping 10.0.201.1
However, if we to send packets to network B or C from router X, we need to add routes so that traffic for these networks is sent on the tunnelling interface.
On router X:
route add -net 10.0.3.1/24 gw 10.0.201.1 dev tunX
route add -net 10.0.4.1/24 gw 10.0.201.1 dev tunX
Similarily, to send packets to network A from router Y, we need to add a route.
On router Y:
route add -net 10.0.2.1/24 gw 10.0.201.2 dev tunY
On router X:
ifconfig tunX down
iptunnel del tunX
(network A)
10.0.2.1, eth1
|
___|_________
| Router X |
|_____________|
| 169.229.255.134 (eth0)
| (Internet or network C)
|
|
| | 10.0.201.1 (tunX)
| |
| |
| | (gre tunnel: 169.229.255.134 <-> 207.241.237.37)
| |
| |
| | 10.0.201.2 (tunY)
|
| (Internet or network C)
| 207.241.237.37 (eth0)
___|___________
| Router Y |
|_______________|
| |
| |
10.0.3.1 10.0.4.1
eth1 eth2
(network B) (network C)
· router X: /etc/network/interfaces
auto tun0
iface tun0 inet static
address 10.0.201.1
netmask 255.255.255.0
broadcast 10.0.201.255
up ifconfig tun0 multicast
pre-up iptunnel add tun0 mode gre remote 207.241.237.37 local 169.229.255.134 ttl 255
pointopoint 10.0.201.2
post-down iptunnel del tun0
· router Y: /etc/network/interfaces
auto tun0
iface tun0 inet static
address 10.0.201.2
netmask 255.255.255.0
broadcast 10.0.201.255
up ifconfig tun0 multicast
pre-up iptunnel add tun0 mode gre local 207.241.237.37 remote 169.229.255.134 ttl 255
pointopoint 10.0.201.1
post-down iptunnel del tun0
· Borrowed heavily from Linux Advanced Routing & Traffic Control HOWTO 
by Bert Hubert et al., 2002
· Discussion on IP tunnels with Quagga 
[转]Creating an IP Tunnel using GRE on Linux,布布扣,bubuko.com
[转]Creating an IP Tunnel using GRE on Linux
标签：style blog http tar com width
原文地址：http://www.cnblogs.com/popsuper1982/p/3800548.html
