标签：drbd
#!/bin/bash
#
# This script is inteded to be used as resource script by heartbeat
#
# Copright 2003-2008 LINBIT Information Technologies
# Philipp Reisner, Lars Ellenberg
#
###
DEFAULTFILE="/etc/default/drbd"
DRBDADM="/sbin/drbdadm"
if [ -f $DEFAULTFILE ]; then
. $DEFAULTFILE
fi
if [ "$#" -eq 2 ]; then
RES="$1"
CMD="$2"
else
RES="all"
CMD="$1"
fi
## EXIT CODES
# since this is a "legacy heartbeat R1 resource agent" script,
# exit codes actually do not matter that much as long as we conform to
# http://wiki.linux-ha.org/HeartbeatResourceAgent
# but it does not hurt to conform to lsb init-script exit codes,
# where we can.
# http://refspecs.linux-foundation.org/LSB_3.1.0/
# LSB-Core-generic/LSB-Core-generic/iniscrptact.html
####
drbd_set_role_from_proc_drbd()
{
local out
if ! test -e /proc/drbd; then
ROLE="Unconfigured"
return
fi
dev=$( $DRBDADM sh-dev $RES )
minor=${dev#/dev/drbd}
if [[ $minor = *[!0-9]* ]] ; then
# sh-minor is only supported since drbd 8.3.1
minor=$( $DRBDADM sh-minor $RES )
fi
if [[ -z $minor ]] || [[ $minor = *[!0-9]* ]] ; then
ROLE=Unknown
return
fi
if out=$(sed -ne "/^ *$minor: cs:/ { s/:/ /g; p; q; }" /proc/drbd); then
set -- $out
ROLE=${5%/*}
: ${ROLE:=Unconfigured} # if it does not show up
else
ROLE=Unknown
fi
}
case "$CMD" in
start)
# try several times, in case heartbeat deadtime
# was smaller than drbd ping time
try=6
while true; do
$DRBDADM primary $RES && break
let "--try" || exit 1 # LSB generic error
sleep 1
done
;;
stop)
# heartbeat (haresources mode) will retry failed stop
# for a number of times in addition to this internal retry.
try=3
while true; do
$DRBDADM secondary $RES && break
# We used to lie here, and pretend success for anything != 11,
# to avoid the reboot on failed stop recovery for "simple
# config errors" and such. But that is incorrect.
# Don‘t lie to your cluster manager.
# And don‘t do config errors...
let --try || exit 1 # LSB generic error
sleep 1
done
;;
status)
if [ "$RES" = "all" ]; then
echo "A resource name is required for status inquiries."
exit 10
fi
ST=$( $DRBDADM role $RES )
ROLE=${ST%/*}
case $ROLE in
Primary|Secondary|Unconfigured)
# expected
;;
*)
# unexpected. whatever...
# If we are unsure about the state of a resource, we need to
# report it as possibly running, so heartbeat can, after failed
# stop, do a recovery by reboot.
# drbdsetup may fail for obscure reasons, e.g. if /var/lock/ is
# suddenly readonly. So we retry by parsing /proc/drbd.
drbd_set_role_from_proc_drbd
esac
case $ROLE in
Primary)
echo "running (Primary)"
exit 0 # LSB status "service is OK"
;;
Secondary|Unconfigured)
echo "stopped ($ROLE)"
exit 3 # LSB status "service is not running"
;;
*)
# NOTE the "running" in below message.
# this is a "heartbeat" resource script,
# the exit code is _ignored_.
echo "cannot determine status, may be running ($ROLE)"
exit 4 # LSB status "service status is unknown"
;;
esac
;;
*)
echo "Usage: drbddisk [resource] {start|stop|status}"
exit 1
;;
esac
exit 0
本文出自 “运维菜鸟” 博客，请务必保留此出处http://ckl893.blog.51cto.com/8827818/1682225
标签：drbd
原文地址：http://ckl893.blog.51cto.com/8827818/1682225
