标签：
这是以前学32的时候写的，那时候学了32之后感觉32真是太强大了，比51强的没影。关于dma网上有许多的资料，关于dma采集ad网上也有很多。亲们搜搜，这里只贴代码了，其实我也想详详细细地叙述一番，但是自己本身打字就慢，还有好多事情要做！代码是我亲自都在板子上测试过的，，当然粘贴/复制过去可能也不会尽如人意，知识这东西总是有许多道不清说不明的东西在里头，往往总是不经一番彻骨寒，哪得梅花扑鼻香。推荐一本书吧！这是野火出的。
这本书自从在图书馆借来就从来没有再放回去，总是在续借。像是在打广告了
#include <stm32f10x.h> #include "ADC1.h" #include "DMA1.h" #include "USART1.h" #include "time.h" #include "stdio.h" extern uint32_t SendBuff; float ADC_Received; uint32_t ADC_Received1; uint8_t ADC_Received2[11]; //printf函数重新定向，方便在程序中使用 int fputc(int ch, FILE *f) { USART_SendData(USART1, (unsigned char) ch); while (!(USART1->SR & USART_FLAG_TXE)); return (ch); } void usart_putchar(uint8_t ch) { USART_SendData(USART1,ch); while(USART_GetFlagStatus(USART1,USART_FLAG_TXE) == RESET); } int main() { ADC1_Config(); DMA_Config(); USART1_Config(); while(1) { // ADC_Received = (float)ADC_GetConversionValue(ADC1)*3.3/4069; // ADC_Received1 = ADC_Received * 1000000000; ADC_Received = (float)SendBuff*3.3/4069; ADC_Received1 = ADC_Received * 1000000000; ADC_Received2[0]=(ADC_Received1/1000000000 + 0x30); //usart_putchar(0x2e); ADC_Received2[1]=(ADC_Received1%1000000000/100000000 + 0x30); ADC_Received2[2]=(ADC_Received1%1000000000%100000000/10000000 + 0x30); ADC_Received2[3]=(ADC_Received1%1000000000%100000000%10000000/1000000 + 0x30); ADC_Received2[4]=(ADC_Received1%1000000000%100000000%10000000%1000000/100000 + 0x30); ADC_Received2[5]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000/10000 + 0x30); ADC_Received2[6]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000%10000/1000 + 0x30); ADC_Received2[7]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000%10000%1000/100 + 0x30); ADC_Received2[8]=(ADC_Received1%1000000000%100000000%10000000%1000000%100000%10000%1000%100/10 + 0x30); ADC_Received2[9]=(ADC_Received1%10 + 0x30); ADC_Received2[10]=0x0d; USART_DMACmd(USART1, USART_DMAReq_Tx, ENABLE); // delay_ms(1000); // USART_DMACmd(USART1, USART_DMAReq_Tx, DISABLE); // delay_ms(1000); // ADC_Received = (float) SendBuff/4069*3.3; // ADC_Received = (u16)ADC1 -> DR; // ADC_Received = (float)ADC_Received/4069*3.3; // printf("\r\n v = %f V \r\n",ADC_Received); // while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC )); // usart_putchar(‘\r‘); // usart_putchar(‘\n‘); // usart_putchar(0x0d); // usart_putchar(0x0a); // printf("\r"); // printf("\n"); // printf("\r\n V = %fv\r\n",ADC_Received); } } #include "ADC1.h" void ADC1_Config(void) { ADC_InitTypeDef ADC_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE); ADC1_Gpio_Config(); ADC_DeInit(ADC1); //复位 ADC1,将外设 ADC1 的全部寄存器重设为缺省值 // ADC1 配置 ADC_InitStructure.ADC_Mode = ADC_Mode_Independent; //ADC1工作在独立模式 ADC_InitStructure.ADC_ScanConvMode = ENABLE;//使能扫描 ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;;//ADC转换工作在连续模式 ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;//由软件控制转换 ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;//转换数据右对齐 ADC_InitStructure.ADC_NbrOfChannel = 1;//转换通道为通道1 ADC_Init(ADC1, &ADC_InitStructure); //初始化ADC //ADC1选择信道0,顺续等级1,采样时间239.5个周期 ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_28Cycles5); //打开ADC1 ADC_Cmd(ADC1, ENABLE); //重置ADC1校准寄存器 ADC_ResetCalibration(ADC1); //等待ADC1校准重置完成 while(ADC_GetResetCalibrationStatus(ADC1)); //开始ADC1校准 ADC_StartCalibration(ADC1); //等待ADC1校准完成 while(ADC_GetCalibrationStatus(ADC1)); //使能ADC1软件开始转换 ADC_SoftwareStartConvCmd(ADC1, ENABLE); //配置ADC时钟=PCLK2 1/6 12MHz RCC_ADCCLKConfig(RCC_PCLK2_Div6); //使能ADC1模块DMA ADC_DMACmd(ADC1, ENABLE); } static void ADC1_Gpio_Config(void) { GPIO_InitTypeDef GPIO_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN; GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0; GPIO_Init(GPIOA , &GPIO_InitStructure); } #include "DMA1.h" /* 其他函数里 USART_DMACmd(USART1, USART_DMAReq_Tx, ENABLE); */ uint32_t SendBuff; extern float ADC_Received; extern uint8_t ADC_Received2[11]; //描述 ：DMA 串口的初始化配置 void DMA_Config(void) { //初始化结构体 DMA_InitTypeDef DMA_InitStructure; //开启DMA时钟 RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); //配置DMA中断 NVIC_Config(); //设置DMA源：地址 DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&ADC1 -> DR; //*内存地址(要传输的变量的指针) DMA_InitStructure.DMA_MemoryBaseAddr = (u32)&SendBuff; //外设作为数据传输的来源 DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; //指定 DMA 通道的 DMA 缓存的大小，单位为数据单位。 DMA_InitStructure.DMA_BufferSize = 1; //*外设地址不增 DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //*内存地址不增 DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Disable; //*外设数据单位数据宽度为 16 位 DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord; //*内存数据单位数据宽度为 16 位 DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord; //*DMA模式：一次传输/循环 // DMA_Mode_Circular 工作在循环缓存模式 // DMA_Mode_Normal 工作在正常缓存模式 // DMA_InitStructure.DMA_Mode = DMA_Mode_Normal ; DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //*优先级：高 DMA_InitStructure.DMA_Priority = DMA_Priority_High; //*禁止内存到内存的传输 DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; //*配置DMA1的1通道 DMA_Init(DMA1_Channel1, &DMA_InitStructure); //使能DMA DMA_Cmd (DMA1_Channel1,ENABLE); //配置DMA发送完成后产生中断 // DMA_ITConfig(DMA1_Channel1,DMA_IT_TC,ENABLE); //****************************************************/// //****************************************************/// //****************************************************/// //设置DMA源：地址 DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&USART1 -> DR; //*内存地址(要传输的变量的指针) DMA_InitStructure.DMA_MemoryBaseAddr = (u32)ADC_Received2; //外设作为数据传输的目的地 DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST; //指定 DMA 通道的 DMA 缓存的大小，单位为数据单位。 DMA_InitStructure.DMA_BufferSize = 11; //*外设地址不增 DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //*内存地址不增 DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; //*外设数据单位数据宽度为 16 位 DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte; //*内存数据单位数据宽度为 16 位 DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte; //*DMA模式：一次传输/循环 // DMA_Mode_Circular 工作在循环缓存模式 // DMA_Mode_Normal 工作在正常缓存模式 // DMA_InitStructure.DMA_Mode = DMA_Mode_Normal ; DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //*优先级：中 DMA_InitStructure.DMA_Priority = DMA_Priority_Medium; //*禁止内存到内存的传输 DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; //*配置DMA1的4通道 DMA_Init(DMA1_Channel4, &DMA_InitStructure); //使能DMA DMA_Cmd (DMA1_Channel4,ENABLE); //配置DMA发送完成后产生中断 // DMA_ITConfig(DMA1_Channel1,DMA_IT_TC,ENABLE); } #include "time.h" /**************** 延时多少个 1/72 us ****************/ void delay_1_72us(uint32_t time) { SysTick -> LOAD = (u32) time; //定时器赋初值 SysTick -> CTRL = 0x00000005; //选择72MHz 并 打开定时器 while(!(SysTick -> CTRL & 0x00010000));//等待计数到零 SysTick -> CTRL = 0x00000004;//关闭定时器 } void delay_ms(u32 time) { while(time -- ) { delay_1_72us(72000); } } #include "USART1.h" //描述 ：USART1 GPIO 配置,工作模式配置。115200 8-N-1 void USART1_Config(void) { GPIO_InitTypeDef GPIO_InitStructure; USART_InitTypeDef USART_InitStructure; // 打开 USART1 的时钟 RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE); // USART1 Tx (PA_9) GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;//复用推挽输出 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOA, &GPIO_InitStructure); // USART1 Tx (PA_10) GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;//浮空输入 GPIO_Init(GPIOA, &GPIO_InitStructure); /* USART1 mode config */ USART_InitStructure.USART_BaudRate = 115200; USART_InitStructure.USART_WordLength = USART_WordLength_8b; USART_InitStructure.USART_StopBits = USART_StopBits_1; USART_InitStructure.USART_Parity = USART_Parity_No ; USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None; USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; USART_Init(USART1, &USART_InitStructure); USART_Cmd(USART1, ENABLE); }
标签：
原文地址：http://www.cnblogs.com/yangfengwu/p/5297147.html
