2.2寸（14PIN）TFT液晶屏STM32 SPI 控制

//默认程序接线说明：
#define LCD_CTRL             GPIOB                //定义TFT数据端口为PB组
#define LCD_LED            GPIO_Pin_9  //MCU_PB9           对应接液晶屏(或者模块)TFT --PIN_LED背光正极（背光可以由IO口提供电流，或者外接3.3V电压）
#define LCD_CS            GPIO_Pin_11 //MCU_PB11            对应接液晶屏(或者模块)TFT --CS
#define LCD_SCL            GPIO_Pin_13    //MCU_PB13            对应接液晶屏(或者模块)TFT --SCL
#define LCD_SDA            GPIO_Pin_15    //MCU_PB15 MOSI    对应接液晶屏(或者模块)TFT --SDA 
#define LCD_SDO            GPIO_Pin_14    //MCU_PB14 MISO    对应接液晶屏(或者模块)TFT --SDO 
#define LCD_RS             GPIO_Pin_10    //MCU_PB10            对应接液晶屏(或者模块)TFT --RS/DC
#define LCD_RST           GPIO_Pin_12    //MCU_PB12            对应接液晶屏(或者模块)TFT --RST

//本测试程序演示功能包括：
//1.纯色填充测试
//2.英文显示测试示例
//3.中文显示测试示例
//4.2D按钮显示测试示例
//5.数码管字体数字显示测试示例
//6.图片显示测试示例
//7.横竖屏切换测试示例

//////////////////////////////////////////////////////////////////////////////////     

/* Includes ------------------------------------------------------------------*/
#include "stm32f10x.h"
#include "Lcd_Driver.h"
#include "GUI.h"
#include "delay.h"
#include "Picture.h"

GPIO_InitTypeDef GPIO_InitStructure;

void RCC_Configuration(void);

void Delayms(__IO uint32_t nCount);

unsigned char Num[10]={0,1,2,3,4,5,6,7,8,9};



void Redraw_Mainmenu(void)
{

    Lcd_Clear(GRAY0);
    
    Gui_DrawFont_GBK16(16,0,BLUE,GRAY0,"全动电子技术");
    Gui_DrawFont_GBK16(16,20,RED,GRAY0,"液晶测试程序");

    DisplayButtonUp(15,38,113,58); //x1,y1,x2,y2
    Gui_DrawFont_GBK16(16,40,YELLOW,GRAY0,"颜色填充测试");

    DisplayButtonUp(15,68,113,88); //x1,y1,x2,y2
    Gui_DrawFont_GBK16(16,70,BLUE,GRAY0,"文字显示测试");

    DisplayButtonUp(15,98,113,118); //x1,y1,x2,y2
    Gui_DrawFont_GBK16(16,100,RED,GRAY0,"图片显示测试");


    Gui_DrawFont_GBK16(16,120,BLUE,GRAY0,"S1:Move.    ");
    Gui_DrawFont_GBK16(16,140,RED,GRAY0, "S2:Sellect  ");
    delay_ms(1000);
    delay_ms(1000);
    /*
    Gui_DrawFont_Num32(100,125,RED,GRAY0,Num[5]);
    delay_ms(1000);
    Gui_DrawFont_Num32(100,125,RED,GRAY0,Num[4]);
    delay_ms(1000);
    Gui_DrawFont_Num32(100,125,RED,GRAY0,Num[3]);
    delay_ms(1000);
    Gui_DrawFont_Num32(100,125,RED,GRAY0,Num[2]);
    delay_ms(1000);
    Gui_DrawFont_Num32(100,125,RED,GRAY0,Num[1]);
    delay_ms(1000);
    Gui_DrawFont_Num32(100,125,RED,GRAY0,Num[0]);    */
}

void Num_Test(void)
{
    u8 i=0;
    Lcd_Clear(GRAY0);
    Gui_DrawFont_GBK16(16,20,RED,GRAY0,"Num Test");
    delay_ms(1000);
    Lcd_Clear(GRAY0);

    for(i=0;i<10;i++)
    {
    Gui_DrawFont_Num32((i%3)*40,32*(i/3)+30,RED,GRAY0,Num[i+1]);
    delay_ms(100);
    }
    delay_ms(1000);
    
}
//文字显示测试全动电子技术商城因为专注所以专业程
void Font_Test(void)
{
    u8 x_offset;
#ifdef H_VIEW  //如果定义了横屏显示
    x_offset=40;
#else
    x_offset=0;
#endif
    Lcd_Clear(GRAY0);
    Gui_DrawFont_GBK16(16,10,BLUE,GRAY0,  "   文字显示测试   ");

    delay_ms(1000);
    Lcd_Clear(WHITE);
    Gui_DrawFont_GBK16(x_offset,10,RED,WHITE,  "     全动电子技术有限公司      ");
    Gui_DrawFont_GBK16(x_offset,30,RED,WHITE,  "         QDtech .,LTD         ");
    Gui_DrawFont_GBK24(x_offset,50,BLUE,WHITE, "           欢迎您            ");
    Gui_DrawFont_GBK16(x_offset,100,GREEN,WHITE,   "     全程技术支持     ");    
    Gui_DrawFont_GBK16(x_offset,120,RED,YELLOW,   "http://qdtech.taobao.com");
    Gui_DrawFont_GBK16(x_offset,140,RED,YELLOW,   "E-Mail:QDtech2008@gmail.com");
    Gui_DrawFont_GBK16(x_offset,160,RED,YELLOW,   "技术交流群:324828016");    
    Gui_DrawFont_GBK16(x_offset,180,BLUE,WHITE,   "Tel:15989313508 ");
    delay_ms(3000);    
}

void Color_Test(void)
{
    u8 i=2;
    Lcd_Clear(GRAY0);
    
    Gui_DrawFont_GBK16(20,10,BLUE,GRAY0,"Color Test");
    delay_ms(1000);

    while(i--)
    {
    Lcd_Clear(WHITE);
    Lcd_Clear(BLACK);
    Lcd_Clear(RED);
      Lcd_Clear(GREEN);
      Lcd_Clear(BLUE);
    }        
}
//16位 垂直扫描  右到左  高位在前
void show_pic(const unsigned char *p)
{
    int i,j;
    unsigned char picH,picL;
    //Lcd_SetRegion(0,0,240-1,240-1);
    for(i=0;i<240;i++)
    for(j=0;j<320;j++)
    {
        picH=*p++;
        picL=*p++;
        Lcd_WriteData(picH);
        Lcd_WriteData(picL);
    }        
} 

u16 ID=0;
int main(void)
{
  //uint16_t a;
  /* System Clocks Configuration **********************************************/
  SystemInit();
  delay_init(72);//延时初始化 
  while(1) 
  {
        Lcd_Init();            
        Lcd_Clear(WHITE);
        LCD_LED_SET;
        //delay_ms(500);
        // LCD_LED_CLR;
        //delay_ms(500);
        //LCD_LED_SET;
        Redraw_Mainmenu();//简单菜单测试
        Color_Test();//简单刷屏测试
        Num_Test();//数码管字体显示
        Font_Test();//中英文测试  
            
        Lcd_Clear(WHITE);  
        show_pic(gImage_123);//图片显示测试
        delay_ms(1000);
        delay_ms(1000);
        Lcd_Clear(WHITE);  
        Gui_DrawFont_GBK16(10,50,BLUE,GRAY0,"测试成功.");
        delay_ms(1000);
  }
 
}


void RCC_Configuration(void)
{   
  /* Setup the microcontroller system. Initialize the Embedded Flash Interface,  
     initialize the PLL and update the SystemFrequency variable. */
  SystemInit();
}


void Delayms(__IO uint32_t nCount)
{
  for(; nCount != 0; nCount--);
}

#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *   where the assert_param error has occurred.
  * @param file: pointer to the source file name
  * @param line: assert_param error line source number
  * @retval : None
  */



void assert_failed(uint8_t* file, uint32_t line)
{ 
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */

  /* Infinite loop */
  while (1)
  {
  }
}
#endif

/******************* (C) COPYRIGHT 2009 STMicroelectronics *****END OF FILE****/