标签：
大纲：
1、创建RAID1
2、创建RAID5
3、创建RAID10
===============================
1、创建RAID1
RAID1原理：需要两块或以上磁盘，可添加热备盘。
在写入数据时，会在另一块磁盘中生成该文件的镜像（即同步）。
两块磁盘中的内容完全一致。
故当一块磁盘损坏时，可使用另一块镜像盘中的数据。（当拥有热备盘时，若镜像盘损坏，可由热备盘替代）
磁盘利用率为50%，即两块100G的磁盘构成RAID1只能提供100G的可用空间。
实战：创建RAID1
第一步：给虚拟机添加三块硬盘，并开机检查。
[root@localhost ~]# ls /dev/sd*
/dev/sda /dev/sda1 /dev/sda2 /dev/sdb /dev/sdc /dev/sdd
[root@localhost ~]#
效果如图：
第二步：分别对三块磁盘分区，并修改其标签
使用相同办法，分别对/dev/sdb、/dev/sdc、/dev/sdd进行分区
[root@localhost ~]# fdisk /dev/sdb
Welcome to fdisk (util-linux 2.23.2).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Device does not contain a recognized partition table
Building a new DOS disklabel with disk identifier 0xeed790f7.
Command (m for help): n
Partition type:
p primary (0 primary, 0 extended, 4 free)
e extended
Select (default p):
Using default response p
Partition number (1-4, default 1):
First sector (2048-41943039, default 2048):
Using default value 2048
Last sector, +sectors or +size{K,M,G} (2048-41943039, default 41943039):
Using default value 41943039
Partition 1 of type Linux and of size 20 GiB is set
Command (m for help): t
Selected partition 1
Hex code (type L to list all codes): fd
Changed type of partition ‘Linux‘ to ‘Linux raid autodetect‘
Command (m for help): p
Disk /dev/sdb: 21.5 GB, 21474836480 bytes, 41943040 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: dos
Disk identifier: 0xeed790f7
Device Boot Start End Blocks Id System
/dev/sdb1 2048 41943039 20970496 fd Linux raid autodetect
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
[root@localhost ~]#
效果如图：
第三步：创建RAID1磁盘阵列
检查三块磁盘是否被其他磁盘阵列使用
mdadm –E /dev/sd[b-d]1
使用分区后的三块磁盘，创建RAID1磁盘阵列
（其中-n指定两块设备，-x指定一个热备盘，-l 指定级别为RAID1 -C创建 -v显示信息 /dev/md1—>指定创建的设备名）
mdadm -Cv /dev/md1 -l 1 -n 2 -x 1 /dev/sd[b-d]1
检查：
[root@localhost ~]# ls /dev/md1
/dev/md1
[root@localhost ~]# mdadm -D /dev/md1
/dev/md1:
Version : 1.2
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Array Size : 20954112 (19.98 GiB 21.46 GB)
Used Dev Size : 20954112 (19.98 GiB 21.46 GB)
Raid Devices : 2
Total Devices : 3
Persistence : Superblock is persistent
Update Time : Sun Aug 21 01:28:01 2016
State : clean
Active Devices : 2
Working Devices : 3
Failed Devices : 0
Spare Devices : 1
Name : localhost.localdomain:1 (local to host localhost.localdomain)
UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Events : 17
Number Major Minor RaidDevice State
0 8 17 0 active sync /dev/sdb1
1 8 33 1 active sync /dev/sdc1
2 8 49 - spare /dev/sdd1
[root@localhost ~]# mdadm -E /dev/md1
mdadm: No md superblock detected on /dev/md1.
[root@localhost ~]# mdadm -E /dev/sd[b-d]1
/dev/sdb1:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x0
Array UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Name : localhost.localdomain:1 (local to host localhost.localdomain)
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Raid Devices : 2
Avail Dev Size : 41908224 (19.98 GiB 21.46 GB)
Array Size : 20954112 (19.98 GiB 21.46 GB)
Data Offset : 32768 sectors
Super Offset : 8 sectors
Unused Space : before=32680 sectors, after=0 sectors
State : clean
Device UUID : 483270f1:90ae6527:ab2ceee6:58ee030d
Update Time : Sun Aug 21 01:28:01 2016
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 5e434c0e - correct
Events : 17
Device Role : Active device 0
Array State : AA (‘A‘ == active, ‘.‘ == missing, ‘R‘ == replacing)
/dev/sdc1:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x0
Array UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Name : localhost.localdomain:1 (local to host localhost.localdomain)
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Raid Devices : 2
Avail Dev Size : 41908224 (19.98 GiB 21.46 GB)
Array Size : 20954112 (19.98 GiB 21.46 GB)
Data Offset : 32768 sectors
Super Offset : 8 sectors
Unused Space : before=32680 sectors, after=0 sectors
State : clean
Device UUID : b6a96682:0ca07895:8fafe1f0:c5761864
Update Time : Sun Aug 21 01:28:01 2016
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : be54c04a - correct
Events : 17
Device Role : Active device 1
Array State : AA (‘A‘ == active, ‘.‘ == missing, ‘R‘ == replacing)
/dev/sdd1:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x0
Array UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Name : localhost.localdomain:1 (local to host localhost.localdomain)
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Raid Devices : 2
Avail Dev Size : 41908224 (19.98 GiB 21.46 GB)
Array Size : 20954112 (19.98 GiB 21.46 GB)
Data Offset : 32768 sectors
Super Offset : 8 sectors
Unused Space : before=32680 sectors, after=0 sectors
State : clean
Device UUID : 9ee8a186:310bc49c:66788d58:ec4b1d9a
Update Time : Sun Aug 21 01:28:01 2016
Bad Block Log : 512 entries available at offset 72 sectors
Checksum : 678c0856 - correct
Events : 17
Device Role : spare
Array State : AA (‘A‘ == active, ‘.‘ == missing, ‘R‘ == replacing)
[root@localhost ~]#
查看磁盘阵列状态信息：
生成配置信息：
[root@localhost ~]# mdadm -Dvs >> /etc/mdadm.conf
[root@localhost ~]# cat !$ # !$ --> 上一条命令最后一个参数
第四步：格式化并挂载
[root@localhost ~]# mkfs.xfs /dev/md1
效果如图：
[root@localhost ~]# mkdir /disk
[root@localhost ~]# mount /dev/md1 /disk
[root@localhost ~]# df –h | tail –1
效果如图：
第五步：设置开机启动
[root@localhost ~]# echo "/dev/md1 /disk xfs defaults 0 0 " >> /etc/fstab
[root@localhost ~]# cat !$
[root@localhost ~]# df | grep /disk
[root@localhost ~]# umount /disk
[root@localhost ~]# mount –a #测试，umount /disk 模拟重启，mount –a 模拟开机
[root@localhost ~]# df | tail –1 #检查挂载结果
注：也可使用 mount –av 查看挂载信息
第六步：RAID1磁盘故障模拟及修复
模拟RAID磁盘故障：
[root@localhost ~]# mdadm -D /dev/md1 #查看/dev/md1状态
/dev/md1:
Version : 1.2
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Array Size : 20954112 (19.98 GiB 21.46 GB)
Used Dev Size : 20954112 (19.98 GiB 21.46 GB)
Raid Devices : 2
Total Devices : 3
Persistence : Superblock is persistent
Update Time : Sun Aug 21 01:43:47 2016
State : clean
Active Devices : 2
Working Devices : 3
Failed Devices : 0
Spare Devices : 1
Name : localhost.localdomain:1 (local to host localhost.localdomain)
UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Events : 17
Number Major Minor RaidDevice State
0 8 17 0 active sync /dev/sdb1
1 8 33 1 active sync /dev/sdc1
2 8 49 - spare /dev/sdd1
[root@localhost ~]# mdadm /dev/md1 -f /dev/sdb1 #设置/dev/sdb1损坏
mdadm: set /dev/sdb1 faulty in /dev/md1
[root@localhost ~]# mdadm -D /dev/md1 #查看/dev/md1状态
/dev/md1:
Version : 1.2
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Array Size : 20954112 (19.98 GiB 21.46 GB)
Used Dev Size : 20954112 (19.98 GiB 21.46 GB)
Raid Devices : 2
Total Devices : 3
Persistence : Superblock is persistent
Update Time : Sun Aug 21 01:44:50 2016
State : clean, degraded, recovering
Active Devices : 1
Working Devices : 2
Failed Devices : 1
Spare Devices : 1
Rebuild Status : 3% complete
Name : localhost.localdomain:1 (local to host localhost.localdomain)
UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Events : 19
Number Major Minor RaidDevice State
2 8 49 0 spare rebuilding /dev/sdd1
1 8 33 1 active sync /dev/sdc1
0 8 17 - faulty /dev/sdb1
[root@localhost ~]#
模拟RAID磁盘故障：
1、停用RAID1磁盘阵列
2、清除/dev/sdb1超级块标识
3、激活RAID1磁盘阵列
4、添加/dev/sdb1到磁盘阵列中
详情如下：
[root@localhost ~]# mdadm /dev/md1 --zero-superblock /dev/sdb1
mdadm: No action given for /dev/md1 in --misc mode
Action options must come before device names
[root@localhost ~]# mdadm --zero-superblock /dev/sdb1 #磁盘阵列挂载并且激活状态下，去除标志是不会成功的
mdadm: Couldn‘t open /dev/sdb1 for write - not zeroing
[root@localhost ~]# mdadm -S /dev/md1 #停用RAID1磁盘阵列
mdadm: Cannot get exclusive access to /dev/md1:Perhaps a running process, mounted filesystem or active volume group?
[root@localhost ~]# df |grep disk
/dev/md1 20943872 32932 20910940 1% /disk
[root@localhost ~]# umount /disk
[root@localhost ~]# mdadm -S /dev/md1 #停用RAID1磁盘阵列
mdadm: stopped /dev/md1
[root@localhost ~]# mdadm --zero-superblock /dev/sdb1 #清除/dev/sdb1超级块标识
[root@localhost ~]# mdadm -As /dev/md1 #激活RAID1磁盘阵列
mdadm: /dev/md1 has been started with 2 drives.
[root@localhost ~]# mdadm -D /dev/md1
/dev/md1:
Version : 1.2
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Array Size : 20954112 (19.98 GiB 21.46 GB)
Used Dev Size : 20954112 (19.98 GiB 21.46 GB)
Raid Devices : 2
Total Devices : 2
Persistence : Superblock is persistent
Update Time : Sun Aug 21 01:49:16 2016
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
Name : localhost.localdomain:1 (local to host localhost.localdomain)
UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Events : 36
Number Major Minor RaidDevice State
2 8 49 0 active sync /dev/sdd1
1 8 33 1 active sync /dev/sdc1
[root@localhost ~]# mdadm /dev/md1 -a /dev/sdb1 #添加/dev/sdb1到磁盘阵列中
mdadm: added /dev/sdb1
[root@localhost ~]# mdadm -D /dev/md1
/dev/md1:
Version : 1.2
Creation Time : Sun Aug 21 01:26:17 2016
Raid Level : raid1
Array Size : 20954112 (19.98 GiB 21.46 GB)
Used Dev Size : 20954112 (19.98 GiB 21.46 GB)
Raid Devices : 2
Total Devices : 3
Persistence : Superblock is persistent
Update Time : Sun Aug 21 01:50:15 2016
State : clean
Active Devices : 2
Working Devices : 3
Failed Devices : 0
Spare Devices : 1
Name : localhost.localdomain:1 (local to host localhost.localdomain)
UUID : 9f8c8a03:8036f47c:788bd593:8c0c83cd
Events : 37
Number Major Minor RaidDevice State
2 8 49 0 active sync /dev/sdd1
1 8 33 1 active sync /dev/sdc1
3 8 17 - spare /dev/sdb1
[root@localhost ~]# mdadm -Dvs >> /etc/mdadm.conf #重新生成配置信息，在磁盘阵列信息发生改变后，要重新生成配置信息
[root@localhost ~]# cat !$
cat /etc/mdadm.conf
ARRAY /dev/md1 level=raid1 num-devices=2 metadata=1.2 spares=1 name=localhost.localdomain:1 UUID=9f8c8a03:8036f47c:788bd593:8c0c83cd
devices=/dev/sdb1,/dev/sdc1,/dev/sdd1
ARRAY /dev/md1 level=raid1 num-devices=2 metadata=1.2 spares=1 name=localhost.localdomain:1 UUID=9f8c8a03:8036f47c:788bd593:8c0c83cd
devices=/dev/sdb1,/dev/sdc1,/dev/sdd1
[root@localhost ~]#
1-15-2-RAID1 企业级RAID磁盘阵列的搭建（RAID1、RAID5、RAID10）
标签：
原文地址：http://www.cnblogs.com/xiaogan/p/5791750.html
