标签：interface 工作原理 实验目的 实验设备 台电脑
实验名称：端口聚合配置
实验目的：理解端口聚合的工作原理，掌握如何在交换机上配置端口聚合。
实验原理：端口聚合（Aggregate-port）又称链路聚合，是指两台交换机之间在物理上将多个端口
连接起来，将多条链路聚合成一条逻辑链路。从而增大链路带宽，解决交换网络中因带宽引
起的网络瓶颈问题。多条物理链路之间能够相互冗余备份，其中任意一条链路断开，不会影
响其他链路的正常转发数据。
端口聚合遵循 IEEE 802.3ad 协议的标准。
实验设备：两台交换机（三层二层各一台），两台电脑（配置生成树信息）
实验步骤：
第一步：配置两台交换机的主机名和管理 IP 地址
S3750#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
S3750(config)#hostname L3-SW
L3-SW(config)#interface vlan 1
L3-SW(config-if)#Dec 3 01:03:22 L3-SW %7:%LINE PROTOCOL CHANGE:
Interface VLAN 1, changed state to UP
L3-SW(config-if)#ip address 192.168.1.1 255.255.255.0
L3-SW(config-if)#no shutdown
L3-SW(config-if)#exit
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname L2-SW
L2-SW(config)#interface vlan 1
L2-SW(config-if)#ip address 192.168.1.2 255.255.255.0
L2-SW(config-if)#no shutdown
L2-SW(config-if)#exit
第二步：在两台交换机上配置聚合端口
L3-SW(config)#interface range fastEthernet 0/1-2
L3-SW(config-if-range)#port-group 1
！将端口 Fa0/1~2 加入聚合端口 1，同时创建该聚合端口
L3-SW(config-if-range)#Dec 3 01:03:57 L3-SW %7:%LINE PROTOCOL CHANGE:
Interface AggregatePort 1, changed state to UP
Dec 3 01:03:58 L3-SW %7:%LINK CHANGED: Interface FastEthernet 0/1, changed
state to administratively down
Dec 3 01:03:58 L3-SW %7:%LINE PROTOCOL CHANGE: Interface FastEthernet
0/1, changed state to DOWN
Dec 3 01:03:58 L3-SW %7:%LINK CHANGED: Interface FastEthernet 0/2, changed
state to administratively down
L3-SW(config-if-range)#exit
L3-SW(config)#
L2-SW(config)#interface range fastEthernet 0/1-2
L2-SW(config-if-range)#port-group 1
！将端口 Fa0/1~2 加入聚合端口 1，同时创建该聚合端口
L2-SW(config-if-range)#exit
L2-SW(config)#
第三步：将聚合端口设置为 Trunk
L3-SW(config)#interface aggregateport 1
L3-SW(config-if)#switchport mode trunk
L3-SW(config-if)#exit
L3-SW(config)#
L2-SW(config)#interface aggregatePort 1
L2-SW(config-if)#switchport mode trunk
L2-SW(config-if)#exit
L2-SW(config)#
第四步：设置聚合端口的负载平衡方式
L3-SW(config)#aggregateport load-balance ?
！查看交换机支持的负载平衡方式
dst-ip Destination IP address
dst-mac Destination MAC address
ip Source and destination IP address
src-dst-mac Source and destination MAC address
src-ip Source IP address
src-mac Source MAC address
L3-SW(config)#aggregateport load-balance dst-mac
！设置负载平衡方式为依据目的地址进行，默认是依据源和目的地址
L3-SW(config)#exit
L2-SW(config)#aggregatePort load-balance ?
！查看交换机支持的负载平衡方式
dst-mac Destination MAC address
ip Source and destination IP address
src-mac Source MAC address
L2-SW(config)#aggregatePort load-balance dst-mac
！设置负载平衡方式为依据目的地址进行，默认是依据源地址
L2-SW(config)#exit
第五步：查看聚合端口的配置
L3-SW#show aggregatePort load-balance
Load-balance : Destination MAC
L3-SW#
L3-SW#show aggregatePort summary
AggregatePort MaxPorts SwitchPort Mode Ports
------------- -------- ---------- ------ ----------------------------------
Ag1 8 Enabled TRUNK Fa0/1 ,Fa0/2
L3-SW#
L3-SW#show interfaces aggregateport 1
Index(dec):29 (hex):1d
AggregatePort 1 is UP , line protocol is UP
Hardware is Aggregate Link AggregatePort
Interface address is: no ip address
MTU 1500 bytes, BW 1000000 Kbit
Encapsulation protocol is Bridge, loopback not set
Keepalive interval is 10 sec , set
Carrier delay is 2 sec
RXload is 1 ,Txload is 1
Queueing strategy: WFQ
Switchport attributes:
interface‘s description:""
medium-type is copper
lastchange time:337 Day: 1 Hour: 3 Minute:56 Second
Priority is 0
admin duplex mode is AUTO, oper duplex is Full
admin speed is AUTO, oper speed is 100M
flow control admin status is AUTO,flow control oper status is OFF
broadcast Strom Control is OFF,multicast Strom Control is OFF,unicast Strom
Control is OFF
Aggregate Port Informations:
Aggregate Number: 1
Name: "AggregatePort 1"
Refs: 2
Members: (count=2)
FastEthernet 0/1 Link Status: Up
FastEthernet 0/2 Link Status: Up
L3-SW#
L2-SW#show aggregatePort load-balance
Load-balance : Destination MAC address
L2-SW#
L2-SW#show aggregatePort summary
AggregatePort MaxPorts SwitchPort Mode Ports
------------- -------- ---------- ------ -----------------------
Ag1 8 Enabled Trunk Fa0/1 , Fa0/2
L2-SW#
L2-SW#show interfaces aggregatePort 1
Interface : AggregatePort 1
Description :
AdminStatus : up
OperStatus : up
Hardware : -
Mtu : 1500
LastChange : 0d:0h:0m:0s
AdminDuplex : Auto
OperDuplex : Full
AdminSpeed : Auto
OperSpeed : 100
FlowControlAdminStatus : Off
FlowControlOperStatus : Off
Priority : 0
Broadcast blocked :DISABLE
Unknown multicast blocked :DISABLE
Unknown unicast blocked :DISABLE
L2-SW#
第六步：验证配置
在三层交换机 L3-SW 上配置另一个用于测试的 VLAN 10，配置 IP 地址为
192.168.10.1/24，然后在二层交换机 L2-SW 上配置默认网关（其作用相当于主机的网关，
交换机可将发往其他网段的数据包提交给网关处理），这样 L2-SW 可以 ping 通
192.168.1.1/24 和 192.168.10.1/24，说明聚合端口的 Trunk 配置已经生效。
L3-SW(config)#vlan 10
L3-SW(config-vlan)#exit
L3-SW(config)#
L3-SW(config)#interface vlan 10
L3-SW(config-if)#iDec 3 01:16:02 L3-SW %7:%LINE PROTOCOL CHANGE:
Interface VLAN 10, changed state to UP
L3-SW(config-if)#ip address 192.168.10.1 255.255.255.0
L3-SW(config-if)#no shutdown
L3-SW(config-if)#exit
L2-SW(config)#ip default-gateway 192.168.1.1
！设置二层交换机的默认网关
L2-SW(config)#exit
L2-SW#
L2-SW#ping 192.168.1.1
Sending 5, 100-byte ICMP Echos to 192.168.1.1,
timeout is 2000 milliseconds.
!!!!!
Success rate is 100 percent (5/5)
Minimum = 1ms Maximum = 1ms, Average = 1ms
L2-SW#ping 192.168.10.1
Sending 5, 100-byte ICMP Echos to 192.168.10.1,
timeout is 2000 milliseconds.
!!!!!
Success rate is 100 percent (5/5)
Minimum = 1ms Maximum = 1ms, Average = 1ms
在三层交换机 L3-SW 上长时间的 ping 二层交换机 L2-SW，然后断开聚合端口中的
Fa0/2 端口：
L3-SW#ping 192.168.1.2 ntimes 1000
Sending 1000, 100-byte ICMP Echoes to 192.168.1.2, timeout is 2 seconds:
< press Ctrl+C to break >
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Success rate is 100 percent (1000/1000), round-trip min/avg/max = 1/1/10 ms
可以看到在断开聚合端口中的 Fa0/2 端口时是没有丢包的。再次实验，此次断开 Fa0/1
端口：
L3-SW#ping 192.168.1.2 ntimes 1000
Sending 1000, 100-byte ICMP Echoes to 192.168.1.2, timeout is 2 seconds:
< press Ctrl+C to break >
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Success rate is 99 percent (999/1000), round-trip min/avg/max = 1/1/10 ms
实验过程图：
本文出自 “12035670” 博客，请务必保留此出处http://12045670.blog.51cto.com/12035670/1860718
标签：interface 工作原理 实验目的 实验设备 台电脑
原文地址：http://12045670.blog.51cto.com/12035670/1860718
