标签:接收 class normal rcc ant amp 启用 过滤 enable
基本流程:
1、初始化CAN模块:
启用CAN时钟
配置CAN功能寄存器(包括位定时,分频等等)
配置CAN过滤器
打开中断
2、初始化I/O口
启用GPIO时钟
打开CAN对应的GPIO引脚
配置重映射(根据实际情况)
3、定义CAN发送结构体,接收结构体
4、开始发送并准备接收总线上信号
5、检查接收邮箱收的数据是否正确
1 void CAN_Config() 2 { 3 CAN_InitTypeDef CAN_InitStructure; 4 CAN_FilterInitTypeDef CAN_FilterInitStructure; 5 GPIO_InitTypeDef GPIO_InitStructure; 6 RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN1,ENABLE); 7 /**Configure the PA11 PA12 to CAN1*/ 8 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 | GPIO_Pin_12; 9 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; 10 GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; 11 GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; 12 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; 13 GPIO_Init(GPIOA,&GPIO_InitStructure); 14 GPIO_PinAFConfig(GPIOA,GPIO_PinSource11,GPIO_AF_CAN1); 15 GPIO_PinAFConfig(GPIOA,GPIO_PinSource12,GPIO_AF_CAN1); 16 17 CAN_DeInit(CAN1); 18 CAN_InitStructure.CAN_ABOM = DISABLE; //自动离线 19 CAN_InitStructure.CAN_AWUM = DISABLE; //自动唤醒 20 CAN_InitStructure.CAN_TTCM = DISABLE; //触发通讯模式 21 CAN_InitStructure.CAN_NART = ENABLE; //禁止报文自动重传 22 CAN_InitStructure.CAN_RFLM = DISABLE; //报文自动覆盖¨ 23 CAN_InitStructure.CAN_TXFP = DISABLE; //优先级判定 24 CAN_InitStructure.CAN_Mode = CAN_Mode_Normal; //工作模式 25 /**configure baudrate 1M */ 26 CAN_InitStructure.CAN_SJW = CAN_SJW_1tq; 27 CAN_InitStructure.CAN_BS1 = CAN_BS1_6tq; 28 CAN_InitStructure.CAN_BS2 = CAN_BS2_8tq; 29 CAN_InitStructure.CAN_Prescaler =20; 30 CAN_Init(CAN1, &CAN_InitStructure); 31 32 CAN_FilterInitStructure.CAN_FilterActivation = ENABLE; //启用过滤 33 CAN_FilterInitStructure.CAN_FilterFIFOAssignment = CAN_FilterFIFO0; //过滤邮箱0 34 CAN_FilterInitStructure.CAN_FilterIdHigh= 0x0000; //过滤ID 35 CAN_FilterInitStructure.CAN_FilterIdLow = 0x0000; 36 CAN_FilterInitStructure.CAN_FilterMaskIdHigh = 0x0000; //过滤ID掩码 37 CAN_FilterInitStructure.CAN_FilterMaskIdLow = 0x0000; 38 CAN_FilterInitStructure.CAN_FilterMode =CAN_FilterMode_IdMask; 39 CAN_FilterInitStructure.CAN_FilterNumber = 0; 40 CAN_FilterInitStructure.CAN_FilterScale = CAN_FilterScale_32bit; 41 CAN_FilterInit(&CAN_FilterInitStructure); 42 43 CAN_ITConfig(CAN1,CAN_IT_FMP0,ENABLE); 44 }
定义CAN结构体:
1 CanTxMsg msg; 2 CanRxMsg RxMsg; 3 4 msg.StdId = 0x09; 5 msg.IDE = CAN_Id_Standard; 6 msg.Data[0]=0x01; 7 msg.DLC=1;
1 void CAN1_RX0_IRQHandler(void) 2 { 3 if(CAN_MessagePending(CAN1,CAN_FIFO0) != RESET) 4 { 5 CAN_ClearITPendingBit(CAN1,CAN_IT_FMP0); 6 CAN_Receive(CAN1,CAN_FIFO0,&RxMsg); 7 msg.Data[0] = RxMsg.Data[2]+1; 8 msg.DLC =1; 9 msg.StdId = 0x02; 10 msg.IDE = CAN_Id_Standard; 11 if(RxMsg.Data[0] ==0x01) 12 { 13 GPIO_ToggleBits(GPIOD,GPIO_Pin_14); 14 } 15 CAN_Transmit(CAN1,&msg); 16 } 17 }
经过实验,在通信波特率为20K下可以正常工作。建议在低速下测试,若通信正常,可以逐步提高通信速率。
标签:接收 class normal rcc ant amp 启用 过滤 enable
原文地址:http://www.cnblogs.com/zh666888/p/6937521.html