标签：frame-relay 交换机 路由器 cisco pvc
Frame Relay现在越来越不流行了，不过在过去的设计中被广泛应用。
所以工作上还是能经常见到的, 这篇博文从二层简单总结下FR的一些概念
在介绍Frame Relay之前，先了解下广播介质和非广播介质的区别：
Broadcast Media （广播介质）： Ethernet 、 Token-Ring、FDDI
特点：
Non-Broadcast Multi Access （NBMA）： Frame Relay、ISDN、ATM etc。
特点：
========三层到二层的地址解析对比=======
广播介质的三层地址解析：远程二层MAC地址和远程三层地址绑定
- IPv4 Adress Resolution Protocol ( ARP)
广播介质的三层地址解析：远程或本地的二层MAC地址和远程三层地址绑定
- 反向ARP用解析远程三层地址到本地二层地址
- 只有直接相连的设备可以进行解析
NBMA 端口类型：
多点接口 - 可连接多个二层链路 & 需要三层到二层的解析 (FR & ATM main interface)
单点接口 - 连接一个二层链路 & 不需要三层到二层解析 （PPP link, FR p2p subinterface)
======================================
1. FR 简介
应用了NBMA - 也就意味着潜在存在三层到二层解析问题
DLCI - Data link Connection Identifier (数字链路识别码）
LMI - Local Management Interface
An interface is by default a "multipoint" interface so, frame-relay inverse-arp is on (for point-to-point, there is no Inverse ARP). IP split horizon checking is disabled by default for Frame Relay encapsulation, so routing updates come in and out the same interface. The routers learn the data-link connection identifiers (DLCIs) they need to use from the Frame Relay switch via LMI updates. The routers then Inverse ARP for the remote IP address and create a mapping of local DLCIs and their associated remote IP addresses.
| Spicey |
|---|
Spicey#show running-config Building configuration... Current configuration : 1705 bytes ! version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Spicey ! ! ! interface Ethernet0 ip address 124.124.124.1 255.255.255.0 ! interface Serial0 ip address 3.1.3.1 255.255.255.0 encapsulation frame-relay frame-relay interface-dlci 140 ! ! router rip network 3.0.0.0 network 124.0.0.0 ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! end |
| Prasit |
|---|
Prasit#show running-config Building configuration... Current configuration : 1499 bytes ! version 12.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Prasit ! ! ! interface Ethernet0 ip address 123.123.123.1 255.255.255.0 ! ! interface Serial1 ip address 3.1.3.2 255.255.255.0 encapsulation frame-relay frame-relay interface-dlci 150 ! ! router rip network 3.0.0.0 network 123.0.0.0 ! ! ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! end |
验证
show frame-relay map
show frame-relay pvc
show frame-relay lmi
ping <device name>
show ip route
Spicey#show frame-relay map
Serial0 (up): ip 3.1.3.2 dlci 140(0x8C,0x20C0), dynamic,
broadcast,, status defined, active
Spicey#show frame-relay pvc
PVC Statistics for interface Serial0 (Frame Relay DTE)
Active Inactive Deleted Static
Local 1 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0
DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0
input pkts 83 output pkts 87 in bytes 8144
out bytes 8408 dropped pkts 0 in FECN pkts0
in BECN pkts 0 out FECN pkts 0 out BECN pkts0
in DE pkts 0 out DE pkts 0
out bcast pkts 41 out bcast bytes 3652
pvc create time 01:31:50, last time pvc status changed 01:28:28
Spicey#show frame-relay lmi
LMI Statistics for interface Serial0 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 550 Num Status msgs Rcvd 552
Num Update Status Rcvd 0 Num Status Timeouts 0
Spicey#ping 123.123.123.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.123.123.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms
Spicey#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS
inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
3.0.0.0/24 is subnetted, 1 subnets
C 3.1.3.0 is directly connected, Serial0
124.0.0.0/24 is subnetted, 1 subnets
C 124.124.124.0 is directly connected, Ethernet0
R 123.0.0.0/8 [120/1] via 3.1.3.2, 00:00:08, Serial0
Prasit#show frame-relay map
Serial1 (up): ip 3.1.3.1 dlci 150(0x96,0x2460), dynamic,
broadcast,, status defined, active
Prasit#show frame-relay pvc
PVC Statistics for interface Serial1 (Frame Relay DTE)
Active Inactive Deleted Static
Local 1 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0
DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1
input pkts 87 output pkts 83 in bytes 8408
out bytes 8144 dropped pkts 0 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 38 out bcast bytes 3464
pvc create time 01:34:29, last time pvc status changed 01:28:05
Prasit#show frame-relay lmi
LMI Statistics for interface Serial1 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 569 Num Status msgs Rcvd 570
Num Update Status Rcvd 0 Num Status Timeouts 0
Prasit#ping 124.124.124.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 124.124.124.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms
Prasit#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS
inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
3.0.0.0/24 is subnetted, 1 subnets
C 3.1.3.0 is directly connected, Serial1
R 124.0.0.0/8 [120/1] via 3.1.3.1, 00:00:19, Serial1
123.0.0.0/24 is subnetted, 1 subnets
C 123.123.123.0 is directly connected, Ethernet0
Frame Relay - 简介及基本配置,布布扣,bubuko.com
标签：frame-relay 交换机 路由器 cisco pvc
原文地址：http://blog.csdn.net/ziyuanzhao/article/details/25300803
