标签：erro 修改 优先级 vlan cond format isp alignment ports
一台h3c s7510E下面连着一台华为s5700交换机，要做链路聚合，经过测试完成配置：
华为交换机配置：
interface Eth-Trunk2 #创建聚合接口，注意要使用默认的manual模式
port link-type trunk #设置接口为trunk模式
port trunk allow-pass vlan 10 #配置允许通过的vlan ID
interface GigabitEthernet0/0/47 #进入要做聚合的接口
undo negotiation auto #取消端口自动配置
eth-trunk 2 #加入聚合接口
#
interface GigabitEthernet0/0/48
undo negotiation auto
eth-trunk 2
[Quidway] display interface Eth-Trunk 1
Eth-Trunk1 current state : UP
Line protocol current state : UP
Description:
Switch Port, Link-type : trunk(configured),
PVID : 1, Hash arithmetic : According to SIP-XOR-DIP,Maximal BW: 2G, Current
BW: 2G, The Maximum Frame Length is 9216
IP Sending Frames‘ Format is PKTFMT_ETHNT_2, Hardware address is 48d5-391d-e605
Current system time: 2017-07-20 09:01:41
Last 300 seconds input rate 2734328 bits/sec, 399 packets/sec
Last 300 seconds output rate 1804536 bits/sec, 369 packets/sec
Input: 42304756 packets, 41316437119 bytes
Unicast: 38125370, Multicast: 775584
Broadcast: 3403802, Jumbo: 0
Discard: 0, Pause: 0
Frames: 0
Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Fragments: 0
Runts: 0, DropEvents: 0
Alignments: 0, Symbols: 0
Ignoreds: 0
Output: 32282015 packets, 16416396025 bytes
Unicast: 31707192, Multicast: 478599
Broadcast: 96224, Jumbo: 0
Discard: 0, Pause: 0
Total Error: 0
Collisions: 0, ExcessiveCollisions: 0
Late Collisions: 0, Deferreds: 0
Buffers Purged: 0
Input bandwidth utilization : 0.14%
Output bandwidth utilization : 0.09%
-----------------------------------------------------
PortName Status Weight
-----------------------------------------------------
GigabitEthernet0/0/47 UP 1
GigabitEthernet0/0/48 UP 1
-----------------------------------------------------
The Number of Ports in Trunk : 2 #成员端口有2个了
The Number of UP Ports in Trunk : 2
[Quidway]
H3c交换机查看
dis link-aggregation verbose
Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing
Port Status: S -- Selected, U -- Unselected
Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,
D -- Synchronization, E -- Collecting, F -- Distributing,
G -- Defaulted, H -- Expired
Aggregation Interface: Bridge-Aggregation3
Aggregation Mode: Static
Loadsharing Type: Shar
Port Status Priority Oper-Key
--------------------------------------------------------------------------------
GE3/0/27 S 32768 2
GE3/0/28 S 32768 2 #两个端口状态都是S即成功
总结：配置期间走了不少弯路，最后发现不同交换机直接配置链路聚合只能都使用手动模式（静态模式）
的lacp，这样就容易成功。
因为是自己亲身体验过的。
H3C：默认是静态模式，下面是配成动态lacp命令
[switch-A-Bridge-Aggregation1]link-aggregation mode dynamic
HW关闭自动协商的命令
[Quidway-GigabitEthernet0/0/1]undo negotiated auto
转发于：http://blog.chinaunix.net/xmlrpc.php?r=blog/article&uid=20794884&id=5759211
少部分按照自己配置的过程做了一些调整了修改。
下面简单介绍下H3C静态lacp和动态lacp
H3C配置静态LACP汇聚组
进入系统视图 system-view
创建汇聚组 link-aggregation group agg-id mode static
进入以太网端口视图 interface interface-type interface-number
将以太网端口加入汇聚组 port link-aggregation group agg-id
动态lacp：
进入系统视图 system-view
配置系统优先级 lacp system-priority system-priority可选 缺省情况下，系统优先级为32768
进入以太网端口视图 interface interface-type interface-number
开启端口LACP协议 lacp enable 缺省情况下，端口的LACP协议处于关闭状态
配置端口优先级 lacp port-priority port-priority 缺省情况下，端口优先级为32768
标签：erro 修改 优先级 vlan cond format isp alignment ports
原文地址：http://www.cnblogs.com/lwsup/p/7209317.html
