records.config文件配置模板

#
#
# Process Records Config File
#
# <RECORD-TYPE> <NAME> <TYPE> <VALUE (till end of line)>
#
#	RECORD-TYPE:	CONFIG, LOCAL
#	NAME:		name of variable
#	TYPE:		INT, STRING, FLOAT
#	VALUE:		Initial value for record
#
#
# *NOTE*: All options covered in this file should be documented in the
#         administration guide or the addendum:
#
#
##############################################################################
#
# System Variables
#
##############################################################################
CONFIG proxy.config.proxy_name STRING localhost.localdomain
CONFIG proxy.config.config_dir STRING etc/trafficserver
CONFIG proxy.config.proxy_binary_opts STRING -M
CONFIG proxy.config.env_prep STRING example_prep.sh
CONFIG proxy.config.temp_dir STRING /tmp
CONFIG proxy.config.alarm_email STRING trafficserver
CONFIG proxy.config.syslog_facility STRING LOG_DAEMON
CONFIG proxy.config.output.logfile STRING traffic.out
CONFIG proxy.config.snapshot_dir STRING snapshots
CONFIG proxy.config.system.mmap_max INT 2097152
##############################################################################
#
# Main threads configuration (worker threads). Also see configurations for
# SSL threads, disk I/O threads and task threads in their respective areas.
#
##############################################################################
CONFIG proxy.config.exec_thread.autoconfig INT 1
CONFIG proxy.config.exec_thread.autoconfig.scale FLOAT 1.000000
CONFIG proxy.config.exec_thread.limit INT 2
CONFIG proxy.config.accept_threads INT 2
##############################################################################
#
# Local Manager
#
##############################################################################
CONFIG proxy.config.admin.admin_user STRING admin
CONFIG proxy.config.admin.number_config_bak INT 3
CONFIG proxy.config.admin.user_id STRING trafficserver
##############################################################################
#
# Process Manager
#
##############################################################################
CONFIG proxy.config.admin.autoconf_port INT 8883 #服务PAC文件的端口。默认为8083
CONFIG proxy.config.process_manager.mgmt_port INT 8884
##############################################################################
#
# In order to only bind a specific IP, use the following config, as in
# the example below. Note - this can contain two addresses, one for IPv4
# sockets and one for IPv6 sockets.
#
##############################################################################
#LOCAL proxy.local.incoming_ip_to_bind STRING 192.168.101.17
#LOCAL proxy.local.incoming_ip_to_bind STRING 192.168.101.17 fc07:192:168:101::17
##############################################################################
#
# Alarm Configuration
#
##############################################################################
   # execute alarm as "<abs_path>/<bin> "<MSG_STRING_FROM_PROXY>""
CONFIG proxy.config.alarm.bin STRING example_alarm_bin.sh
CONFIG proxy.config.alarm.abs_path STRING NULL
##############################################################################
#
# HTTP Engine
#
##############################################################################
   ##########
   # basics #
   ##########
   # The server ports are listed here. These are separated by spaces or commas.
   # Each port is a colon separated list of values, which must include a
   # port number. Other options are
   # ipv4 - Use IPv4 (default)
   # ipv6 - Use IPv6
   # tr-in - Transparent inbound.
   # tr-out - Transparent outbound.
   # tr-full - Fully transparent (inbound and outbound).
   # ssl - SSL terminated port.
   # blind - Blind tunnel port.
   # ip-in=[addr] - Bind inbound IP address (listen for client).
   # ip-out=[addr] - Bind outbound IP address (connect to origin server).
   #
   # note - address types must agree with each other and the ipv4/ipv6
   # option if specified. IPv6 addresses must be enclosed in brackets.
   # ip-out can be repeated as long as each address is a different family.
   # The ‘=‘ is optional.
   #
   # Example: Port 8080 IPv6 inbound transparent, and port 80 IPv4
   # "8080:ipv6:tr-in 80"
CONFIG proxy.config.http.server_ports STRING 8828 80 81 82 8080 8081 9999
   # Ports on the origin server to which a blind tunnel may connect.
CONFIG proxy.config.http.connect_ports STRING 563
   # The via settings have four values
   #  0 - Do not modify / set this via header
   #  1 - Update the via, with normal verbosity
   #  2 - Update the via, with higher verbosity
   #  3 - Update the via, with highest verbosity
CONFIG proxy.config.http.insert_request_via_str INT 1
CONFIG proxy.config.http.insert_response_via_str INT 0
   # Insert a Server: header, this has three values
   #   0 - Don‘t add or modify the Server: header
   #   1 - Add a Server: header
   #   2 - Only add a Server: header if one doesn‘t exist already
CONFIG proxy.config.http.response_server_enabled INT 0
CONFIG proxy.config.http.insert_age_in_response INT 0
CONFIG proxy.config.http.enable_url_expandomatic INT 0
CONFIG proxy.config.http.no_dns_just_forward_to_parent INT 0
CONFIG proxy.config.http.uncacheable_requests_bypass_parent INT 0
CONFIG proxy.config.http.keep_alive_enabled_in INT 1
CONFIG proxy.config.http.keep_alive_enabled_out INT 1
CONFIG proxy.config.http.chunking_enabled INT 1
   # send http11 requests:
   #   0 - Never
   #   1 - Always
   #   2 - if the server has returned http1.1 before
   #   3 - if the client request is 1.1 & the server
   #         has returned 1.1 before
CONFIG proxy.config.http.send_http11_requests INT 1
   # Share server connections
   #  0 - Never
   #  1 - Share, with a single global connection pool
   #  2 - Share, with a connection pool per worker thread
CONFIG proxy.config.http.share_server_sessions INT 2
CONFIG proxy.config.http.origin_server_pipeline INT 1
CONFIG proxy.config.http.user_agent_pipeline INT 8
   ##########################
   # HTTP referer filtering #
   ##########################
CONFIG proxy.config.http.referer_filter INT 0
CONFIG proxy.config.http.referer_format_redirect INT 0
CONFIG proxy.config.http.referer_default_redirect STRING http://www.example.com/
   ##############################
   # parent proxy configuration #
   ##############################
CONFIG proxy.config.http.parent_proxy_routing_enable INT 0  #父节点缓存选项
CONFIG proxy.config.http.parent_proxy.retry_time INT 300
   # Parent fail threshold is the number of request that must
   # fail within the retry window for the parent to be marked
   # down
CONFIG proxy.config.http.parent_proxy.fail_threshold INT 10
CONFIG proxy.config.http.parent_proxy.total_connect_attempts INT 4
CONFIG proxy.config.http.parent_proxy.per_parent_connect_attempts INT 2
CONFIG proxy.config.http.parent_proxy.connect_attempts_timeout INT 30
CONFIG proxy.config.http.forward.proxy_auth_to_parent INT 0
   ###################################
   # HTTP connection timeouts (secs) #
   ###################################
   # in:  ua -> proxy connection
   # out: proxy -> origin server connection
   # note: active_timeout is for the total elasped time of the connection,
   # inactivity_timeout is the elapsed time from the time a read or a write
   # was scheduled during which the connection was unable to sink/provide data.
   #
   # proxy.config.http.transaction_active_timeout_in is not available,
   # i think because ua can always active if data not send-out.
   # 0 means not time-out scheduled
   #
CONFIG proxy.config.http.keep_alive_no_activity_timeout_in INT 115
CONFIG proxy.config.http.keep_alive_no_activity_timeout_out INT 120
CONFIG proxy.config.http.transaction_no_activity_timeout_in INT 30
CONFIG proxy.config.http.transaction_no_activity_timeout_out INT 60
CONFIG proxy.config.http.transaction_active_timeout_out INT 0
CONFIG proxy.config.http.accept_no_activity_timeout INT 60
CONFIG proxy.config.http.background_fill_active_timeout INT 14400
CONFIG proxy.config.http.background_fill_completed_threshold FLOAT 0.000000
   ##################################
   # origin server connect attempts #
   ##################################
CONFIG proxy.config.http.connect_attempts_max_retries INT 3
CONFIG proxy.config.http.connect_attempts_max_retries_dead_server INT 3
CONFIG proxy.config.http.connect_attempts_rr_retries INT 3
CONFIG proxy.config.http.connect_attempts_timeout INT 30
CONFIG proxy.config.http.post_connect_attempts_timeout INT 900
CONFIG proxy.config.http.down_server.cache_time INT 300
CONFIG proxy.config.http.down_server.abort_threshold INT 10
   ##################################
   # congestion control             #
   ##################################
CONFIG proxy.config.http.congestion_control.enabled INT 0 #拥塞控制选项
   #############################
   # negative response caching #
   #############################
CONFIG proxy.config.http.negative_caching_enabled INT 0
CONFIG proxy.config.http.negative_caching_lifetime INT 1800
   #########################
   # proxy users variables #
   #########################
CONFIG proxy.config.http.anonymize_remove_from INT 0
CONFIG proxy.config.http.anonymize_remove_referer INT 0
CONFIG proxy.config.http.anonymize_remove_user_agent INT 0
CONFIG proxy.config.http.anonymize_remove_cookie INT 0
CONFIG proxy.config.http.anonymize_remove_client_ip INT 0
CONFIG proxy.config.http.anonymize_insert_client_ip INT 0
CONFIG proxy.config.http.anonymize_other_header_list STRING NULL
CONFIG proxy.config.http.insert_squid_x_forwarded_for INT 1
   ############
   # security #
   ############
CONFIG proxy.config.http.push_method_enabled INT 1
#  ###################################
#  # HTTP Quick filtering (security) #
#  ###################################
#  this functionality is moved to ip_allow.config
   #################
   # cache control #
   #################
CONFIG proxy.config.http.cache.http INT 1   #对象缓存功能
CONFIG proxy.config.http.cache.ignore_client_no_cache INT 1  #1为忽略客户端请求旁路缓存
CONFIG proxy.config.http.cache.ims_on_client_no_cache INT 1  
CONFIG proxy.config.http.cache.ignore_server_no_cache INT 0  #1为忽略服务器请求旁路缓存
CONFIG proxy.config.http.cache.ignore_client_cc_max_age INT 1
CONFIG proxy.config.http.normalize_ae_gzip INT 1
   # cache responses to cookies has 5 options:
   #   0 - do not cache any responses to cookies
   #   1 - cache for any content-type
   #   2 - cache only for image types
   #   3 - cache for all but text content-types
   #   4 - cache for all but text content-types except OS response
   #       without "Set-Cookie" or with "Cache-Control: public"
   # See also cache-responses-to-cookies in cache.config.
CONFIG proxy.config.http.cache.cache_responses_to_cookies INT 3 #指定ATS缓存cookied内容的方式：0=不缓存任何cookies响应；1=缓存所有的cookies响应。2=只缓存图片类型的cookies响应。3=缓存除了文本内容类型的所有cookies响应。
CONFIG proxy.config.http.cache.ignore_authentication INT 0   #1为缓存带www-Authenticate头部的对象
CONFIG proxy.config.http.cache.cache_urls_that_look_dynamic INT 1  #1为缓存动态内容
CONFIG proxy.config.http.cache.enable_default_vary_headers INT 1
   #  when_to_revalidate has 5 options:
   #    0 - default. use cache directives or heuristic
   #    1 - stale if heuristic
   #    2 - always stale (always revalidate)
   #    3 - never stale
   #    4 - always revalidate if request is conditional, else default is used
CONFIG proxy.config.http.cache.when_to_revalidate INT 4  #重新生效HTTP对象
   # Some old MSIE browsers don‘t send no-cache headers to
   # reverse proxies or transparent caches, this variable controls
   # when to add no-cache headers to MSIE requests:
   #  -1 - no-cache is never added, stats are not updated
   #   0 - default; no-cache not added to MSIE requests
   #   1 - no-cache added to IMS MSIE requests
   #   2 - no-cache added to all MSIE requests
CONFIG proxy.config.http.cache.when_to_add_no_cache_to_msie_requests INT -1
   # required headers: three options:
   #   0 - No required headers to make document cachable
   #   1 - "Last-Modified:", "Expires:", or "Cache-Control: max-age" required
   #   2 - explicit lifetime required, "Expires:" or "Cache-Control: max-age"
CONFIG proxy.config.http.cache.required_headers INT 0             #指定头部；0=对头部没有特殊要求
CONFIG proxy.config.http.cache.max_stale_age INT 604800
CONFIG proxy.config.http.cache.range.lookup INT 1
   ########################
   # heuristic expiration #
   ########################
CONFIG proxy.config.http.cache.heuristic_min_lifetime INT 3600     #指定没有截止时间的HTTP对象在缓存中有效期的最小值
CONFIG proxy.config.http.cache.heuristic_max_lifetime INT 86400    #指定没有截止时间的HTTP对象在缓存中有效期的最大值
CONFIG proxy.config.http.cache.heuristic_lm_factor FLOAT 0.100000   #指定计算有效期的老化因子。traffic server存储对象的时间依赖于这个变量。默认值为0.1
CONFIG proxy.config.http.cache.fuzz.time INT 240
CONFIG proxy.config.http.cache.fuzz.probability FLOAT 0.005000
   #########################################
   # dynamic content & content negotiation #
   #########################################
CONFIG proxy.config.http.cache.vary_default_text STRING NULL
CONFIG proxy.config.http.cache.vary_default_images STRING NULL
CONFIG proxy.config.http.cache.vary_default_other STRING NULL
   ##############################################################
   # The HTTP stats are expensive, turn off you don‘t need them #
   ##############################################################
CONFIG proxy.config.http.enable_http_stats INT 1
##############################################################################
#
# Customizable User Response Pages
#
##############################################################################
   # 0 - turn off customizable user response pages
   # 1 - enable customizable user response pages in only the "default" directory
   # 2 - enable language-targeted user response pages
CONFIG proxy.config.body_factory.enable_customizations INT 0
CONFIG proxy.config.body_factory.enable_logging INT 0
   # 0 - never suppress generated responses
   # 1 - always suppress generated responses
   # 2 - suppress responses for intercepted traffic
CONFIG proxy.config.body_factory.response_suppression_mode INT 0
##############################################################################
#
# Net Subsystem
#
##############################################################################
CONFIG proxy.config.net.connections_throttle INT 300000
   # Enable defer accept / accept filtering. On Linux, this is a timeout, sec.
CONFIG proxy.config.net.defer_accept INT 45
##############################################################################
#
# Cluster Subsystem
#
##############################################################################
   # cluster type requires restart to change
   # 1 is full clustering, 2 is mgmt only, 3 is no clustering
LOCAL proxy.local.cluster.type INT 3
CONFIG proxy.config.cluster.cluster_port INT 8086
CONFIG proxy.config.cluster.rsport INT 8088
CONFIG proxy.config.cluster.mcport INT 8089
CONFIG proxy.config.cluster.mc_group_addr STRING 224.0.1.37
CONFIG proxy.config.cluster.mc_ttl INT 1
CONFIG proxy.config.cluster.log_bogus_mc_msgs INT 1
CONFIG proxy.config.cluster.ethernet_interface STRING lo
##############################################################################
#
# Cache
#
##############################################################################
CONFIG proxy.config.cache.permit.pinning INT 0
   # default the ram cache size to AUTO_SIZE (-1) based on cache size
   #   (approximately 1 MB of RAM cache per GB of disk cache)
   # alternatively, set to a fixed value such as 20971520 (20MB)
CONFIG proxy.config.cache.ram_cache.size INT 6324355072 #指定RAM缓存的大小
CONFIG proxy.config.cache.ram_cache_cutoff INT 10485760
   # Replacement algorithm
   #  0 : Clocked Least Frequently Used by Size (CLFUS) w/optional compression
   #  1 : LRU w/o optional compression - trivially simple
CONFIG proxy.config.cache.ram_cache.algorithm INT 1
   # Filter inserts into the RAM cache to ensure that they have been seen at
   # least once.  For LRU, this provides scan resistance. Note that CLFUS
   # already requires that a document have history before it is inserted, so
   # for CLFUS, setting this option means that a document must be seen three
   # times before it is added to the RAM cache.
CONFIG proxy.config.cache.ram_cache.use_seen_filter INT 0
   # Compress the content of the ram cache:
   #  0 : no compression
   #  1 : fastlz (extremely fast, relatively low compression)
   #  2 : libz (moderate speed, reasonable compression)
   #  3 : liblzma (very slow, high compression)
   #  NOTE: compression runs on task threads.  To use more cores for
   #  compression, increase proxy.config.task_threads.
CONFIG proxy.config.cache.ram_cache.compress INT 0
   # The maximum number of alternates that are allowed for any given URL.
   # It is not possible to strictly enforce this if the variable
   #   ‘proxy.config.cache.vary_on_user_agent‘ is set to 1.
   # The default value for ‘proxy.config.cache.vary_on_user_agent‘ is 0.
   # (0 disables the maximum number of alts check)
CONFIG proxy.config.cache.limits.http.max_alts INT 5
   # The target size of a contiguous fragment on disk.
   # Acceptable values are powers of 2, e.g. 65536, 131072, 262144, 524288, 1048576, 2097152.
   # Larger could waste memory on slow connections, smaller could waste seeks.
CONFIG proxy.config.cache.target_fragment_size INT 1048576
   # The maximum size of a document that will be stored in the cache.
   # (0 disables the maximum document size check)
CONFIG proxy.config.cache.max_doc_size INT 0 #指定缓存中对象允许的最大（字节）。0表示没有大小限制
   # enable the cache to read from an object while it is being added to the cache
CONFIG proxy.config.cache.enable_read_while_writer INT 1
   # This controls how many objects (average) the disk caches can hold, and
   # how much memory it‘ll consume for the directory structure.
CONFIG proxy.config.cache.min_average_object_size INT 32768
   # How many I/O threads to allocate per disk (spindle). Be aware that RAID
   # disks would show up to TS as a single spindle.
CONFIG proxy.config.cache.threads_per_disk INT 8
   # Time (in ms) to delay until retrying to acquire a cache lock. Setting
   # this low can reduce latencies in some cases, but can consume more CPU.
   # If you experience CPU spinning, try increasing this setting.
CONFIG proxy.config.cache.mutex_retry_delay INT 2
   # The ssd storage disks. This must be raw disks.
LOCAL proxy.config.cache.ssd.storage STRING NULL
   # The transistor range threshold to hold hot doc in ssd (defalut: 1G).
CONFIG proxy.config.cache.ssd.transistor_range_threshold INT 1073741824
##############################################################################
#
# DNS
#
##############################################################################
CONFIG proxy.config.dns.search_default_domains INT 0
CONFIG proxy.config.dns.splitDNS.enabled INT 0 #分离DNS
CONFIG proxy.config.dns.max_dns_in_flight INT 2048
   # Additional URL expansions for http DNS lookup
CONFIG proxy.config.dns.url_expansions STRING NULL
CONFIG proxy.config.dns.round_robin_nameservers INT 0
CONFIG proxy.config.dns.nameservers STRING NULL
CONFIG proxy.config.dns.resolv_conf STRING /etc/resolv.conf
   # This provides additional resilience against DNS forgery, particularly in
   # forward or transparent proxies, but requires that the resolver populates
   # the queries section of the response properly.
CONFIG proxy.config.dns.validate_query_name INT 0
##############################################################################
#
# HostDB
#
##############################################################################
   # in entries, may not be changed while running
   # note that in order to increase hostdb.size, hostdb.storage_size should
   # also be increase. These are best guesses, you will have to monitor this.
CONFIG proxy.config.hostdb.size INT 50000
CONFIG proxy.config.hostdb.storage_size INT 104857600
   # ttl modes:
   #   0 = obey
   #   1 = ignore
   #   2 = min(X,ttl)
   #   3 = max(X,ttl)
CONFIG proxy.config.hostdb.ttl_mode INT 2
   # in minutes...
CONFIG proxy.config.hostdb.timeout INT 5
   # round-robin addresses for single clients
   # (can cause authentication problems)
CONFIG proxy.config.hostdb.strict_round_robin INT 0
##############################################################################
#
# Logging Config
#
##############################################################################
   # possible values for logging_enabled:
   #   0: no logging at all
   #   1: log errors only
   #   2: log transactions only
   #   3: full logging (errors + transactions)
CONFIG proxy.config.log.logging_enabled INT 3
CONFIG proxy.config.log.max_secs_per_buffer INT 5
CONFIG proxy.config.log.max_space_mb_for_logs INT 111147
CONFIG proxy.config.log.max_space_mb_for_orphan_logs INT 25
CONFIG proxy.config.log.max_space_mb_headroom INT 1000
CONFIG proxy.config.log.hostname STRING localhost
CONFIG proxy.config.log.logfile_dir STRING var/log/trafficserver
CONFIG proxy.config.log.logfile_perm STRING rw-r--r--
CONFIG proxy.config.log.custom_logs_enabled INT 1
CONFIG proxy.config.log.squid_log_enabled INT 0
CONFIG proxy.config.log.squid_log_is_ascii INT 0
CONFIG proxy.config.log.squid_log_name STRING squid
CONFIG proxy.config.log.squid_log_header STRING NULL
CONFIG proxy.config.log.common_log_enabled INT 0
CONFIG proxy.config.log.common_log_is_ascii INT 1
CONFIG proxy.config.log.common_log_name STRING common
CONFIG proxy.config.log.common_log_header STRING NULL
CONFIG proxy.config.log.extended_log_enabled INT 0
CONFIG proxy.config.log.extended_log_is_ascii INT 0
CONFIG proxy.config.log.extended_log_name STRING extended
CONFIG proxy.config.log.extended_log_header STRING NULL
CONFIG proxy.config.log.extended2_log_enabled INT 0
CONFIG proxy.config.log.extended2_log_is_ascii INT 1
CONFIG proxy.config.log.extended2_log_name STRING extended2
CONFIG proxy.config.log.extended2_log_header STRING NULL
CONFIG proxy.config.log.separate_icp_logs INT 0
CONFIG proxy.config.log.separate_host_logs INT 0
   # Log collation allows you to do "remote logging"
LOCAL proxy.local.log.collation_mode INT 0
CONFIG proxy.config.log.collation_host STRING NULL
CONFIG proxy.config.log.collation_port INT 8085
CONFIG proxy.config.log.collation_secret STRING foobar
CONFIG proxy.config.log.collation_host_tagged INT 0
CONFIG proxy.config.log.collation_retry_sec INT 5
CONFIG proxy.config.log.rolling_enabled INT 1
CONFIG proxy.config.log.rolling_interval_sec INT 86400
CONFIG proxy.config.log.rolling_offset_hr INT 0
CONFIG proxy.config.log.rolling_size_mb INT 10
CONFIG proxy.config.log.auto_delete_rolled_files INT 1
CONFIG proxy.config.log.sampling_frequency INT 1
##############################################################################
#
# Reverse Proxy
#
##############################################################################
CONFIG proxy.config.reverse_proxy.enabled INT 0  #HTTP反向代理模式
CONFIG proxy.config.header.parse.no_host_url_redirect STRING NULL
##############################################################################
#
# URL Remap Rules
#
##############################################################################
CONFIG proxy.config.url_remap.default_to_server_pac INT 0
CONFIG proxy.config.url_remap.default_to_server_pac_port INT -1
   # To enable forward proxy, you must turn off remap_required
CONFIG proxy.config.url_remap.remap_required INT 1
   # Pristine host header is the "original" (request) header. Make sure your
   # origin expects them in reverse proxy.
CONFIG proxy.config.url_remap.pristine_host_hdr INT 0
##############################################################################
#
# SSL Termination
#
##############################################################################
   # proxy.config.ssl.enabled should be:
   #   0 - none
   #   1 - SSL enabled
   # Deprecated. SSL is enabled automatically if an SSL port is configured
   # in config.proxy.http.server_ports.
#CONFIG proxy.config.ssl.enabled INT 0
   # The number of SSL threads is a multiplier of number of CPUs and
   # proxy.config.exec_thread.autoconfig.scale by default. You can
   # override that here (set it to a non-zero value).
CONFIG proxy.config.ssl.number.threads INT 0
   # The following three variables can be
   # set to 0 to disable SSLv2, SSLv3, and/or TLSv1.
   # SSLv2 is disabled by default for security concern.
CONFIG proxy.config.ssl.SSLv2 INT 0
CONFIG proxy.config.ssl.SSLv3 INT 1
CONFIG proxy.config.ssl.TLSv1 INT 1
   # The following two variables control the Cipher Suite traffic Server
   # uses for HTTPS connnections and whether to prefer the client
   # selected (default) or the server selected
   # Our default SSL Cipher Suite tries to be reasonably fast and strong.
CONFIG proxy.config.ssl.server.cipher_suite STRING RC4-SHA:AES128-SHA:DES-CBC3-SHA:AES256-SHA:ALL:!aNULL:!EXP:!LOW:!MD5:!SSLV2:!NULL
CONFIG proxy.config.ssl.server.honor_cipher_order INT 0
   # Control if SSL should perform content compression or not
CONFIG proxy.config.ssl.compression INT 0
   # Deprecated.
   # SSL ports should now be configured via proxy.config.http.server_ports
#CONFIG proxy.config.ssl.server_port INT 443
   # Client certification level should be:
   # 0 no client certificates
   # 1 client certificates optional
   # 2 client certificates required
CONFIG proxy.config.ssl.client.certification_level INT 0
   # Server cert chain filename is the name of the cert chain file
   # for a single cert system.
CONFIG proxy.config.ssl.server.cert_chain.filename STRING NULL
   # This is the path that SSL certificates files are relative to. Certificate
   # names specified in ssl_multicert.config will be located relative to this path.
CONFIG proxy.config.ssl.server.cert.path STRING etc/trafficserver
   # If any private key is not contained in the certificate file, you must
   # fill in the private key path. Private key names specified in
   # ssl_multicert.config will be located relative to this path.
CONFIG proxy.config.ssl.server.private_key.path STRING etc/trafficserver
   # The CA file name and path are the
   # certificate authority certificate that
   # client certificates will be verified against.
CONFIG proxy.config.ssl.CA.cert.filename STRING NULL
CONFIG proxy.config.ssl.CA.cert.path STRING etc/trafficserver
   ################################
   # client related configuration #
   ################################
CONFIG proxy.config.ssl.client.verify.server INT 0
CONFIG proxy.config.ssl.client.cert.filename STRING NULL
CONFIG proxy.config.ssl.client.cert.path STRING etc/trafficserver
   # Fill in private key file and path only if the client‘s
   # private key is not contained in the client certificate file.
CONFIG proxy.config.ssl.client.private_key.filename STRING NULL
CONFIG proxy.config.ssl.client.private_key.path STRING etc/trafficserver
   # The CA file name and path are the
   # certificate authority certificate that
   # server certificates will be verified against.
CONFIG proxy.config.ssl.client.CA.cert.filename STRING NULL
CONFIG proxy.config.ssl.client.CA.cert.path STRING etc/trafficserver
##############################################################################
#
# ICP Configuration. NOTE! ICP is currently broken NOTE!
#
##############################################################################
   # icp modes
   #   enabled=0 ICP disabled
   #   enabled=1 Allow receive of ICP queries
   #   enabled=2 Allow send/receive of ICP queries
CONFIG proxy.config.icp.enabled INT 0
CONFIG proxy.config.icp.icp_interface STRING NULL
CONFIG proxy.config.icp.icp_port INT 3130
CONFIG proxy.config.icp.multicast_enabled INT 0
CONFIG proxy.config.icp.query_timeout INT 2
##############################################################################
#
# Scheduled Update Configuration
#
##############################################################################
CONFIG proxy.config.update.enabled INT 0     #指定是否开启更新
CONFIG proxy.config.update.force INT 0   #设置强制立刻更新 0为关闭 1为开启
CONFIG proxy.config.update.retry_count INT 10
CONFIG proxy.config.update.retry_interval INT 2
CONFIG proxy.config.update.concurrent_updates INT 100
##############################################################################
#
# Socket send/recv buffer sizes (0 == don‘t call setsockopt() )
#
##############################################################################
   # out: proxy -> os connection
   # in : ua -> proxy connection
CONFIG proxy.config.net.sock_send_buffer_size_in INT 262144
CONFIG proxy.config.net.sock_recv_buffer_size_in INT 0
CONFIG proxy.config.net.sock_send_buffer_size_out INT 0
CONFIG proxy.config.net.sock_recv_buffer_size_out INT 0
##############################################################################
#
# User Overridden Configurations Below
#
##############################################################################
CONFIG proxy.config.core_limit INT -1
##############################################################################
#
# Debugging
#
##############################################################################
  # Uses a regular expression to match the debugging topic name, performance
  # will be affected!
CONFIG proxy.config.diags.debug.enabled INT 0
CONFIG proxy.config.diags.debug.tags STRING http.*|dns.*
  # Great for tracking down memory leaks, but you need to use the
  # ink allocators
CONFIG proxy.config.dump_mem_info_frequency INT 0
##############################################################################
#
# Configuration for Reclaimable InkFreeList memory pool
#
# NOTE: The following options are no meaningful unless compiles TrafficServer
#	with ‘--enable-reclaimable-freelist‘ option. Looks like:
#	$ ./configure --enable-reclaimable-freelist
#
##############################################################################
  # Dump debug information according bit mask of debug_filter, if a bit is set
  # in the mask, then debug information of the corresponding action are dumped:
  #  bit 0: reclaim memory in ink_freelist_new
  #  bit 1: allocate memory from partial-free Chunks(if exist) or OS
  # NOTE: This option make no sense unless compiles TrafficServer
  #       with ‘--enable-reclaimable-freelist‘ option.
CONFIG proxy.config.allocator.debug_filter INT 0
  # The value of enable_reclaim should be 0 or 1. Default 1, reclaim enabled.
  # NOTE: This option make no sense unless compiles TrafficServer
  #       with ‘--enable-reclaimable-freelist‘ option.
CONFIG proxy.config.allocator.enable_reclaim INT 1
  # The value of reclaim_factor should be in 0.0 ~ 1.0, allocator use it to
  # calculate average value of idle memory in InkFreeList, which will determine
  # when to reclaim memory. The larger the value, the faster the reclaiming.
  # This value is effective only when enable_reclaim is 1.
  # NOTE: This option make no sense unless compiles TrafficServer
  #       with ‘--enable-reclaimable-freelist‘ option.
CONFIG proxy.config.allocator.reclaim_factor FLOAT 0.300000
  # Allocator will reclaim memory only when it continuously satisfy the reclaim
  # condition for max_overage times. This value is effective only when
  # enable_reclaim is 1.
  # NOTE: This option make no sense unless compiles TrafficServer
  #       with ‘--enable-reclaimable-freelist‘ option.
CONFIG proxy.config.allocator.max_overage INT 3
##############################################################################
#
# Slow Log
#
##############################################################################
  # Log any request that takes more then x number of milliseconds, needs
  # to be > 0 to be enabled
CONFIG proxy.config.http.slow.log.threshold INT 0
##############################################################################
#
# Thread pool for "misc" tasks, plugins etc. 2 is a good minimum.
#
##############################################################################
CONFIG proxy.config.task_threads INT 2
CONFIG proxy.config.cluster.cluster_configuration STRING cluster.config
CONFIG proxy.config.http_ui_enabled INT 3 
CONFIG proxy.config.http.cache.ignore_accept_mismatch INT 2
CONFIG proxy.config.http.cache.ignore_accept_language_mismatch INT 2
CONFIG proxy.config.http.cache.ignore_accept_encoding_mismatch INT 2
CONFIG proxy.config.http.cache.ignore_accept_charset_mismatch INT 2
CONFIG proxy.config.http.enable_http_info INT 1
CONFIG proxy.config.dns.lookup_timeout INT 10
CONFIG proxy.config.dns.dedicated_thread INT 1
CONFIG proxy.config.hostdb.lookup_timeout INT 20
CONFIG proxy.config.cache.read_while_writer.max_delay INT 5000
CONFIG proxy.config.http.range_read_ww_enabled INT 1
CONFIG proxy.config.body_factory.template_sets_dir STRING etc/trafficserver/body_factory
CONFIG proxy.config.cache.control.filename STRING cache.config
CONFIG proxy.config.cache.ip_allow.filename STRING ip_allow.config
CONFIG proxy.config.log.xml_config_file STRING logs_xml.config
CONFIG proxy.config.url_remap.filename STRING remap.config
CONFIG proxy.config.ssl.server.multicert.filename STRING ssl_multicert.config