高可用集群中fence的配置

标签：100%   get   physical   /etc/   ott   rip   wan   serial   启动   

先了解什么是fence

每个节点之间互相发送探测包进行判断节点的存活性。一般会有专门的线路进行探测，这条线路称为“心跳线”（上图直接使用eth0线路作为心跳线）。假设node1的心跳线出问题，则node2和node3会认为node1出问题，然后就会把资源调度在node2或者node3上运行，但node1会认为自己没问题不让node2或者node3抢占资源，此时就出现了脑裂(split brain)。

此时如果在整个环境里有一种设备直接把node1断电，则可以避免脑裂的发生，这种设备叫做fence或者stonith(Shoot The Other Node In The Head爆头哥)。

在物理机里virsh是通过串口线管理guestos的，比如virsh destroy nodeX，这里我们把物理机当成fence设备。

配置fence设备

在物理机上

[root@server ~]# mkdir /etc/cluster

[root@server ~]# dd if=/dev/zero of=/etc/cluster/fence_xvm.key bs=1K count=4

记录了4+0 的读入

记录了4+0 的写出

4096字节(4.1 kB)已复制，0.00021345 秒，19.2 MB/秒

[root@server ~]#
在三台节点上创建/etc/cluster

[root@node1 ~]# mkdir /etc/cluster

[root@node2 ~]# mkdir /etc/cluster

[root@node3 ~]# mkdir /etc/cluster

把物理机上创建的/etc/cluster/fence_xvm.key同步到三台节点

[root@server ~]# for i in 1 2 3

> do

> scp /etc/cluster/fence_xvm.key node${i}:/etc/cluster/

> done

root@node1's password: redhat

fence_xvm.key     100% 4096     4.0KB/s   00:00    

root@node2's password: redhat

fence_xvm.key     100% 4096     4.0KB/s   00:00    

root@node3's password: redhat

fence_xvm.key     100% 4096     4.0KB/s   00:00    

[root@server ~]#

在物理机上安装fence-virtd

[root@server ~]# yum install fence-virt* -y

已加载插件：langpacks, product-id, subscription-manager

This system is not registered to Red Hat Subscription Management. You can use subscription-manager to register.

base     | 4.1 kB  00:00:00     

base1    | 4.1 kB  00:00:00     

base2    | 4.1 kB  00:00:00     

正在解决依赖关系

–> 正在检查事务

…..

已安装:

  fence-virtd.x86_64 0:0.3.2-1.el7   fence-virt.x86_64 0:0.3.2-1.el7               fence-virtd-libvirt.x86_64 0:0.3.2-1.el7       fence-virtd-multicast.x86_64 0:0.3.2-1.el7      

  fence-virtd-serial.x86_64 0:0.3.2-1.el7                                                                                                          

完毕！

[root@server ~]#

执行

[root@server ~]# fence_virtd -c

Module search path [/usr/lib64/fence-virt]: 回车

Available backends:

    libvirt 0.1

Available listeners:

    multicast 1.2

    serial 0.4

Listener modules are responsible for accepting requests

from fencing clients.

Listener module [multicast]: 回车

The multicast listener module is designed for use environments

where the guests and hosts may communicate over a network using

multicast.

The multicast address is the address that a client will use to

send fencing requests to fence_virtd.

Multicast IP Address [225.0.0.12]: 回车

Using ipv4 as family.

Multicast IP Port [1229]: 回车

Setting a preferred interface causes fence_virtd to listen only

on that interface.  Normally, it listens on all interfaces.

In environments where the virtual machines are using the host

machine as a gateway, this *must* be set (typically to virbr0).

Set to 'none' for no interface.

Interface [virbr0]: 回车

The key file is the shared key information which is used to

authenticate fencing requests.  The contents of this file must

be distributed to each physical host and virtual machine within

a cluster.

Key File [/etc/cluster/fence_xvm.key]: 回车

Backend modules are responsible for routing requests to

the appropriate hypervisor or management layer.

Backend module [libvirt]: 回车

Configuration complete.

….

=== End Configuration ===

Replace /etc/fence_virt.conf with the above [y/N]? y

[root@server ~]#

启动fence_virtd服务并设置开机自动启动

[root@server ~]# systemctl start fence_virtd

[root@server ~]# systemctl enable fence_virtd

ln -s '/usr/lib/systemd/system/fence_virtd.service' '/etc/systemd/system/multi-user.target.wants/fence_virtd.service'

[root@server ~]#

每个节点安装fence-virt*

[root@nodeX ~]# yum install fence-virt* -y

已加载插件：product-id, subscription-manager

This system is not registered to Red Hat Subscription Management. You can use subscription-manager to register.

base                                                                                                                    | 4.1 kB  00:00:00     

base1                                                                                                                   | 4.1 kB  00:00:00     

base2                                                                                                                   | 4.1 kB  00:00:00     

正在解决依赖关系

–> 正在检查事务

….

nmap-ncat.x86_64 2:6.40-4.el7         numad.x86_64 0:0.5-14.20140620git.el7                                  

qemu-img.x86_64 10:1.5.3-86.el7       radvd.x86_64 0:1.9.2-7.el7                                             

rsyslog-mmjsonparse.x86_64 0:7.4.7-7.el7_0                           unbound-libs.x86_64 0:1.4.20-19.el7    yajl.x86_64 0:2.0.4-4.el7                                           

完毕！

[root@nodeX ~]#

因为我们在第一节已经关闭了stonith，这里先启用它：

点击“Appliy Changes”

创建fence

Type选择fence_xvm

Fence Instance Name用于区分不同的fence设备，这里填写fence1

展开Advanced Arguments

pcmk_host_list处填写这个fence可以管理哪些节点，这里填写node1,node2,node3，用英文逗号隔开。

点击"Create Fance Instance"

等待一会即可看到fence正常运行

手动的fence掉某个节点

高可用集群中fence的配置

标签：100%   get   physical   /etc/   ott   rip   wan   serial   启动   

原文地址：http://blog.51cto.com/lduan/2071552