码迷,mamicode.com
首页 > 其他好文 > 详细

H3C室外无线AP(WA4320X)胖瘦切换设置方法

时间:2018-05-29 15:29:56      阅读:1302      评论:0      收藏:0      [点我收藏+]

标签:无线   AP   H3C   固件   刷新   

    因客户有一台H3CWA4320X无线AP是有胖、瘦切换的功能,但在出厂时默认为瘦模式,无线AP上并没有两种模式的切换开关,打电话给厂家说是刷新固件才能支持为胖模式。于是我使用串口线连接AP上的console口进行调试。

    1、查看一下无线AP当前的配置,发现无IP地址:

[WA4320X]dis cur

#

 version 5.20, Release 1508P11

#

 sysname WA4320X

#

telnet server enable

#

 password-recovery enable

#

vlan 1

#

interface NULL0

#

interface Vlan-interface1

#

interface GigabitEthernet1/0/1

#

interface WLAN-Radio1/0/1

#

interface WLAN-Radio1/0/2

   2、手动添加IP地址为192.168.0.50,为传输文件做准备

[WA4320X]int vlan 1

[WA4320X-Vlan-interface1]ip address 192.168.0.50 24

[WA4320X-Vlan-interface1]qu

   3、在电脑上打开3CD服务器:

技术分享图片

   4、设备好本机的IP地址和无线AP同一网段,使用网线连接APGE1

技术分享图片

   5、删除AP上的瘦版本

<WA4320X>delete /unreserved wa4300_fit.bin

The contents cannot be restored!!! Delete flash:/wa4300_fit.bin?[Y/N]:y

Deleting a file permanently will take a long time. Please wait...

%Apr 26 12:03:25:284 2000 WA4320X WMSH/6/WMESH_EXIT_ZERO_CFG_STATE:  The device has exited zero configuration state.

%Delete file flash:/wa4300_fit.bin...Done.

   6、把要刷新的固件文件改名为wa4300_fat.bin,并放到3CDaemon目录下

技术分享图片

   

   7、把胖版本传到AP上,并用它dir查看版本已经在AP上:

<WA4320X>tftp 192.168.0.51 get wa4300_fat.bin

File will be transferred in binary mode

  Downloading file from remote TFTP server, please wait...\

%Apr 26 12:06:30:290 2000 WA4320X WMSH/6/WMESH_ENTER_ZERO_CFG_STATE:  The device has entered zero configuration state./

TFTP: 11062272 bytes received in 35 second(s)

  File downloaded successfully.

<WA4320X> dir /all

Directory of flash:/

 

   0     -rw-  11062272  Apr 26 2000 12:07:03   wa4300_fat.bin

 

130688 KB total (118730 KB free)

    8、设置下次启动文件,:

<WA4320X>boot-loader file flash:/wa4300_fat.bin

%Apr 26 12:07:55:424 2000 WA4320X WMSH/6/WMESH_EXIT_ZERO_CFG_STATE:  The device has exited zero configuration state.

  Verifying boot file ......

%Apr 26 12:08:00:868 2000 WA4320X WMSH/6/WMESH_ENTER_ZERO_CFG_STATE:  The device has entered zero configuration state.

  This command will set the boot file. Continue? [Y/N]:

Before pressing ENTER you must choose 'YES' or 'NO'[Y/N]:

Before pressing ENTER you must choose 'YES' or 'NO'[Y/N]:

Before pressing ENTER you must choose 'YES' or 'NO'[Y/N]:y

  The specified file will be used as the boot file at the next reboot on slot 1!

 

      9、使用reboot重启设备,web页面登陆http://192.168.0.50,可以登陆表示胖模式刷新成功。

技术分享图片





H3C室外无线AP(WA4320X)胖瘦切换设置方法

标签:无线   AP   H3C   固件   刷新   

原文地址:http://blog.51cto.com/lijie1977/2121554

(0)
(0)
   
举报
评论 一句话评论(0
登录后才能评论!
© 2014 mamicode.com 版权所有  联系我们:gaon5@hotmail.com
迷上了代码!