标签：cto The pac oss nssa brief cond 结果 ip route
案例：HSRP配置在企业网络到外部的连接方案中，要求不高的条件下可以是单出口。一旦该出口线路出现问题，整个企业网络就不能连接到外网了。为了使得企业网络到外网连接的高可用性，可以设置两个以上的出口，然而多个出口对于内网主机意味着我个网关。主机不能同时使用多个网关，当主机所使用的网关出现故障时，它不能实现网关的自动切换。
配置热备份路由协议1.2 方案
在出口设备上配置热备份路由协议（HSRP），组成一个HSRP组，组内两个出口设备共享一个虚拟IP地址，该IP地址作为内网主机的网关。
HSRP组成员有主备之分，虚拟IP地址被附加到主设备上。如果主设备线路出故障，备份设备会成为主设备，虚拟IP地址也会迁移过来。这样，不管哪一个出口设备出现问题，不管哪个出口设备在提供外网接入，内网主机的网关都不需要改变。
网络拓扑图如图－1所示：
图－1
1.3 步骤
实现此案例需要按照如下步骤进行。
步骤一：分别在三台路由器上配置端口IP地址
tarena-R1(config)# interface f0/0
tarena-R1(config-if)#ip address 192.168.1.252 255.255.255.0
tarena-R1(config-if)#no shutdown
tarena-R1(config-if)#interface f0/1
tarena-R1(config-if)#ip address 192.168.2.1 255.255.255.0
tarena-R1(config-if)#no shutdown
tarena-R2(config)#interface f0/0
tarena-R2(config-if)#ip address 192.168.1.253 255.255.255.0
tarena-R2(config-if)#no shutdown
tarena-R2(config-if)#interface f0/1
tarena-R2(config-if)#ip address 192.168.3.1 255.255.255.0
tarena-R2(config-if)#no shutdown
tarena-R3(config)#interface f0/0
tarena-R3(config-if)#ip address 192.168.2.2 255.255.255.0
tarena-R3(config-if)#no shutdown
tarena-R3(config-if)#interface f0/1
tarena-R3(config-if)#ip address 192.168.3.2 255.255.255.0
tarena-R3(config-if)#no shutdown
tarena-R3(config-if)#interface f1/0
tarena-R3(config-if)#ip address 192.168.4.254 255.255.255.0
tarena-R3(config-if)#no shutdown步骤二：在R1和R2上配置到外网的默认路由
tarena-R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.2.2
tarena-R1(config)#end
tarena-R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 192.168.1.2 to network 0.0.0.0
C 192.168.1.0/24 is directly connected, FastEthernet0/0
C 192.168.2.0/24 is directly connected, FastEthernet0/1
S* 0.0.0.0/0 [1/0] via 192.168.2.2
tarena-R1#
tarena-R2(config)#ip route 0.0.0.0 0.0.0.0 192.168.3.2
tarena-R2(config)#exit
tarena-R2#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 192.168.2.2 to network 0.0.0.0
C 192.168.1.0/24 is directly connected, FastEthernet0/0
C 192.168.3.0/24 is directly connected, FastEthernet0/1
S* 0.0.0.0/0 [1/0] via 192.168.3.2步骤三：在R3上配置到企业内网的静态路由
tarena-R3(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.1
tarena-R3(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1
tarena-R3(config)#end
tarena-R3#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
S 192.168.1.0/24 [1/0] via 192.168.2.1
[1/0] via 192.168.3.1
C 192.168.2.0/24 is directly connected, FastEthernet0/0
C 192.168.3.0/24 is directly connected, FastEthernet0/1
C 192.168.4.0/24 is directly connected, FastEthernet1/0
tarena-R3#步骤四：在R1上配置HSRP，指定其优先级为200
HSRP的默认优先级为100，路由器启动后，根据优先级决定谁可以成为活跃路由器，优先级高的将胜出。如果路由器优先级相同，再比较端口IP地址，IP地址大的成为活路跃路由器。
另外，如果优先级低的路由器先启动了，它将成为活跃路由器。优先级高的路由器启动后，发现已有活跃路由器存在，它将接受现状，直到活跃路由器出现故障它才会在重新选举时成为活跃角色。
tarena-R1(config)#interface f0/0
tarena-R1(config-if)#standby 1 ip 192.168.1.254
tarena-R1(config-if)#standby 1 priority 200
%HSRP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Speak -> Standby
%HSRP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Standby -> Active配置HSRP后，通过输出日志可以观察到路由器角色的改变。
步骤五：在R2上配置HSRP，指定其优先级为195
tarena-R2(config)#interface f0/0
tarena-R2(config-if)#standby 1 ip 192.168.1.254
tarena-R2(config-if)#standby 1 priority 195
%HSRP-6-STATECHANGE: FastEthernet0/0 Grp 1 state Speak -> Standby步骤六：分别在R1和R2上查看HSRP信息
tarena-R1#show standby brief
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Fa0/0 1 200 Active local 192.168.1.253 192.168.1.254
tarena-R2#show standby brief
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Fa0/0 1 195 Standby 192.168.2.252 local 192.168.1.254步骤七：在内部主机上测试到外网主机的连通性
SERVER>ipconfig
FastEthernet0 Connection:(default port)
Link-local IPv6 Address.........: FE80::207:ECFF:FE80:557D
IP Address......................: 192.168.1.1
Subnet Mask.....................: 255.255.255.0
Default Gateway.................: 192.168.1.254
PC>ping 192.168.4.1
Pinging 192.168.4.1 with 32 bytes of data:
Reply from 192.168.4.1: bytes=32 time=0ms TTL=126
Reply from 192.168.4.1: bytes=32 time=0ms TTL=126
Reply from 192.168.4.1: bytes=32 time=0ms TTL=126
Reply from 192.168.4.1: bytes=32 time=1ms TTL=126
Ping statistics for 192.168.4.1
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 1ms, Average = 0ms步骤八：在R1配置端口跟踪、R2配置占先权
tarena-R1(config)#interface fastEthernet 0/0
tarena-R1(config-if)#standby 1 track f0/1
tarena-R2(config)#interface fastEthernet 0/0
tarena-R2(config-if)#standby 1 preempt步骤九：关闭R1的f0/1接口，模拟设备故障，查看R2的HSRP信息
tarena-R1(config)#interface fastEthernet 0/1
tarena-R1(config-if)#shutdown
tarena-R2#show standby brief
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Fa0/0 1 195 Active local unknown 192.168.1.254结果显示R2已成为活跃路由器，而备份路由器状态未知。虚拟路由器的IP地址192.168.1.254/24也已迁移到R2上了。
步骤十：在R1配置占先权，并激活R1的f0/1接口并查状态
备份路由器成为活跃路由器后，原来的活跃路由器R1即使线路修复也不会重新成为进入活跃状态。
为了使路由器完全根据优先级来决定其状态，需要配置占先权。占先权保证了严格根据优先级来决定哪台设备进入活跃状态。
tarena-R1(config)#interface f0/0
tarena-R1(config-if)#standby 1 preempt
tarena-R1(config)#interface f0/1
tarena-R1(config-if)#no shutdown
tarena-R1#show standby brief
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Fa0/0 1 200 Active local 192.168.1.253 192.168.1.254标签：cto The pac oss nssa brief cond 结果 ip route
原文地址：http://blog.51cto.com/13735155/2134633
