标签：ns3   proc   start   必须   cal   lvs   网卡ip   响应   oca   

1.1 环境信息

NOTE: 需要打开核心转发功能, “net.ipv4.ip_forward = 1”, 拓扑图参考基础概念中lvs-nat模型图.

1.2 配置步骤

1. director

$ yum install -y ipvsadm

$ ipvsadm -A -t 172.29.2.60:80 -s rr 
$ ipvsadm -a -t 172.29.2.60:80 -r 192.168.123.101:80 -m
$ ipvsadm -a -t 172.29.2.60:80 -r 192.168.123.102:80 -m

$ ipvsadm -L -n
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
  -> RemoteAddress:Port           Forward Weight ActiveConn InActConn
TCP  172.29.2.60:80 rr
  -> 192.168.123.101:80           Masq    1      0          0         
  -> 192.168.123.102:80           Masq    1      0          0         

2. Real-server1

$ yum install -y httpd

$ echo -e "<title>web1</title>\n<h1>webserver1</>\n" > /var/www/html/index.html 
$ cat /var/www/html/index.html
<title>web1</title>
<h1>webserver1</>

$ systemctl start httpd

3. Real-server2

$ yum install -y httpd

$ echo -e "<title>web2</title>\n<h1>webserver2</h1>\n" > /var/www/html/index.html
$ cat /var/www/html/index.html
<title>web2</title>
<h1>webserver2</h1>

$ systemct start httpd

4. 测试: 通过VIP进行访问

$ curl http://172.29.2.60
<title>web2</title>
<h1>webserver2</h1>

$ curl http://172.29.2.60
<title>web1</title>
<h1>webserver1</>

也可以用浏览器进行访问测试.

5. 查看连接状态

$ ipvsadm -lnc

二、lvs-dr

2.1 环境信息

• arp_ignore:
  • 0: 响应任意网卡上接受到的对本机IP地址的arp请求(包括回环往卡上的地址), 而不管该目的IP是否在接收往卡上
  • 1: 只响应目的IP地址为接收网卡上的本地地址的ARP请求
  • 2: 只响应目的IP地址为接收网卡上的本地地址的ARP请求, 并且arp请求的源IP必须和接收网卡同网段
  • 3: 如果arp请求数据包所请求的IP地址对应的本地地址其作用域(scope)为主机(host), 则不会因arp响应数据包, 如果作用域为全局(global)或链路(link), 则回应arp响应数据包
  • 4~7: 保留未使用
  • 8: 不回应所有的arp请求
• arp_announce:
  • 允许使用任意网卡IP地址作为arp请求的源IP, 通常就是用数据包的源IP
  • 尽量避免使用不属于该发送网卡子网卡的本地地址作为发送arp请求的源IP地址
  • 忽略IP数据包的源IP地址, 选择该发送网卡上最合适的本地地址作为arp请求的源IP地址

2.2 配置步骤

1. director

$ ifconfig ens33:0 192.168.123.110/32 broadcast 192.168.123.110 up
$ route add -host 192.168.123.110 dev ens33:0
$ route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.123.2   0.0.0.0         UG    0      0        0 ens33
169.254.0.0     0.0.0.0         255.255.0.0     U     1002   0        0 ens33
192.168.123.0   0.0.0.0         255.255.255.0   U     0      0        0 ens33
192.168.123.110 0.0.0.0         255.255.255.255 UH    0      0        0 ens33

$ ipvsadm -A -t 192.168.123.110:80 -s rr
$ ipvsadm -a -t 192.168.123.110:80 -r 192.168.123.101 -g
$ ipvsadm -a -t 192.168.123.110:80 -r 192.168.123.102 -g
$ ipvsadm -L -n
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
  -> RemoteAddress:Port           Forward Weight ActiveConn InActConn
TCP  192.168.123.110:80 rr
  -> 192.168.123.101:80           Route   1      0          0         
  -> 192.168.123.102:80           Route   1      0          0         

2. Real-Server1

$ echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore 
$ echo 1 > /proc/sys/net/ipv4/conf/ens33/arp_ignore     
$ echo 2 > /proc/sys/net/ipv4/conf/ens33/arp_announce 
$ echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce

$ ifconfig lo:0 192.168.123.110/32 broadcast 192.168.123.110 up
$ route add -host 192.168.123.110 dev lo:0

3. Real-Server2

$ echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore 
$ echo 1 > /proc/sys/net/ipv4/conf/ens33/arp_ignore     
$ echo 2 > /proc/sys/net/ipv4/conf/ens33/arp_announce 
$ echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce

$ ifconfig lo:0 192.168.123.110/32 broadcast 192.168.123.110 up
$ route add -host 192.168.123.110 dev lo:0

lvs(3) - nat和dr模型演示

标签：ns3   proc   start   必须   cal   lvs   网卡ip   响应   oca   

原文地址：http://blog.51cto.com/13501622/2147293