标签：cat   view   ado   huawei   ber   ssi   获得   51cto   col   

一、 配置pppoe服务器

• 1.将AR2配置为pppoe服务器

<Huawei> sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sysn  SERVER
[SERVER]ip pool pool1      //配置一个地址池pool1
Info: It‘s successful to create an IP address pool.
[SERVER-ip-pool-pool1]network  10.1.12.0  mask 255.255.255.0
[SERVER-ip-pool-pool1]gateway-list 10.1.12.254
[SERVER-ip-pool-pool1]quit
[SERVER]interface Virtual-Template 1    //配置一个虚拟接口
Jul 29 2018 23:44:49-08:00 SERVER %%01IFPDT/4/IF_STATE(l)[0]:Interface Virtual-T
emplate1 has turned into UP state.
[SERVER-Virtual-Template1]ppp authentication-mode chap    //配置认证模式为chap
[SERVER-Virtual-Template1]ip add 10.1.12.254 24
[SERVER-Virtual-Template1]remote address pool pool1          //分配ip地址
[SERVER-Virtual-Template1]quit

• 2.在AR2上的g0/0/0接口绑定虚拟模板

[SERVER]int g0/0/0
[SERVER-GigabitEthernet0/0/0]pppoe-server bind virtual-template 1  //绑定virtual-template 1
[SERVER-GigabitEthernet0/0/0]quit

• 3.为pppoE被认证方创建账户和密码

[SERVER]aaa
[SERVER-aaa]local-user zh password cipher huawei    
Info: Add a new user.
[SERVER-aaa]local-user zh service-type ppp
[SERVER-aaa]quit

二、配置pppoe客户端

• 4.将AR1配置为pppoe客户端

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname AR1
[AR1]dialer-rule             //进入dialer-rule视图
[AR1-dialer-rule]dialer-rule 1 ip permit     //允许ip流量触发拨号
[AR1-dialer-rule]quit
[AR1]interface dialer 1                 //创建并进入dialer 1接口
[AR1-Dialer1]
Jul 29 2018 23:47:33-08:00 AR1 %%01IFPDT/4/IF_STATE(l)[0]:Interface Dialer1 has 
turned into UP state.
[AR1-Dialer1]dialer user zh          //配置用户对端用户名，这个用户名需与服务器端的ppp用户名相同
[AR1-Dialer1]dialer-group 1         //将接口置于一个拨号访问组
[AR1-Dialer1]dialer bundle 1      
[AR1-Dialer1]ppp chap user zh      //指定dialer 1 接口的编号（用于和物理接口绑定）
[AR1-Dialer1]ppp chap password  cipher huawei
[AR1-Dialer1]dialer timer idle 300        //设置按需pppoe拨号的空闲时间（300s没有流量就断开）
INFO:  The configuration will become effective after link reset.
[AR1-Dialer1]ip address ppp-negotiate    //ip地址协商

• 5.将pppoe拨号接口绑定到出接口

[AR1-Dialer1]interface g0/0/0
[AR1-GigabitEthernet0/0/0]pppoe-client dial-bundle-number 1  
[AR1-GigabitEthernet0/0/0]quit

• 6.配置本端到服务器的缺省静态路由

  [AR1]ip route-static 0.0.0.0 0.0.0.0 Dialer 1

三、验证

• 7.在SERVER上执行display pppoe-server session all和display virtual-access命令，查看PPPoE会话的状态和配置信息。

• 8.查看AR1上的拨号接口的信息，并确认拨号接口能够从PPPoE服务器获得IP地址。

<AR1>display ip interface brief

华为pppoe配置实战演练

标签：cat   view   ado   huawei   ber   ssi   获得   51cto   col   

原文地址：http://blog.51cto.com/12184141/2152988