led driver 0--一个简单但完整的字符设备驱动程序

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/fs.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <asm/uaccess.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/arch/regs-gpio.h>
#include <asm/hardware.h>

#define DEVICE_NAME     "leds"  /* 加载模式后，执行”cat /proc/devices”命令看到的设备名称 */
#define LED_MAJOR       231     /* 主设备号 */


static struct class *leds_class;
static struct class_device    *leds_class_devs[4];


/* bit0<=>D10, 0:亮, 1:灭
 *  bit1<=>D11, 0:亮, 1:灭
 *  bit2<=>D12, 0:亮, 1:灭
 */
static char leds_status = 0x0;
static DECLARE_MUTEX(leds_lock); // 定义赋值

//static int minor;
static unsigned long gpio_va;

#define GPIO_OFT(x) ((x) - 0x56000000)
#define GPFCON  (*(volatile unsigned long *)(gpio_va + GPIO_OFT(0x56000050)))//oo00:GPFCON  0x56000050  R/W  配置端口F的引脚
#define GPFDAT  (*(volatile unsigned long *)(gpio_va + GPIO_OFT(0x56000054)))//oo00:gpio_va + 0x54 ，把物理地址0x56000054映射为虚拟地址GPFDAT。
//led驱动中，要操作io口，必须要把物理地址映射为虚拟地址。


/* 应用程序对设备文件/dev/leds执行open(...)时，
 * 就会调用s3c24xx_leds_open函数
 */
static int s3c24xx_leds_open(struct inode *inode, struct file *file)
{
    int minor = MINOR(inode->i_rdev); //MINOR(inode->i_cdev);

    switch(minor)
    {
        case 0: /* /dev/leds */
        {
            // 配置3引脚为输出
            //s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP);
            GPFCON &= ~(0x3<<(4*2)); //oo00:这里GPFCON是虚拟地址，在驱动模块开始的时候，这个虚拟地址已经通过宏定义 #define GPFCON  (*(volatile unsigned long *)(gpio_va + GPIO_OFT(0x56000050)))被映射到物理地址
            GPFCON |= (1<<(4*2));

            //s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP);
            GPFCON &= ~(0x3<<(5*2));
            GPFCON |= (1<<(5*2));

            //s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP);
            GPFCON &= ~(0x3<<(6*2));
            GPFCON |= (1<<(6*2));

            // 都输出0
            //s3c2410_gpio_setpin(S3C2410_GPF4, 0);
            GPFDAT &= ~(1<<4);

            //s3c2410_gpio_setpin(S3C2410_GPF5, 0);
            GPFDAT &= ~(1<<5);
            //s3c2410_gpio_setpin(S3C2410_GPF6, 0);
            GPFDAT &= ~(1<<6);

            down(&leds_lock);
            leds_status = 0x0;
            up(&leds_lock);

            break;
        }

        case 1: /* /dev/led1 */
        {
            s3c2410_gpio_cfgpin(S3C2410_GPF4, S3C2410_GPF4_OUTP);
            s3c2410_gpio_setpin(S3C2410_GPF4, 0);

            down(&leds_lock);
            leds_status &= ~(1<<0);
            up(&leds_lock);

            break;
        }

        case 2: /* /dev/led2 */
        {
            s3c2410_gpio_cfgpin(S3C2410_GPF5, S3C2410_GPF5_OUTP);
            s3c2410_gpio_setpin(S3C2410_GPF5, 0);
            leds_status &= ~(1<<1);
            break;
        }

        case 3: /* /dev/led3 */
        {
            s3c2410_gpio_cfgpin(S3C2410_GPF6, S3C2410_GPF6_OUTP);
            s3c2410_gpio_setpin(S3C2410_GPF6, 0);

            down(&leds_lock);
            leds_status &= ~(1<<2);
            up(&leds_lock);

            break;
        }

    }

    return 0;
}



static int s3c24xx_leds_read(struct file *filp, char __user *buff,
                                         size_t count, loff_t *offp)
{
    int minor = MINOR(filp->f_dentry->d_inode->i_rdev);
    char val;

    switch (minor)
    {
        case 0: /* /dev/leds */
        {
            copy_to_user(buff, (const void *)&leds_status, 1);
            break;
        }

        case 1: /* /dev/led1 */
        {
            down(&leds_lock);
            val = leds_status & 0x1;
            up(&leds_lock);
            copy_to_user(buff, (const void *)&val, 1);
            break;
        }

        case 2: /* /dev/led2 */
        {
            down(&leds_lock);
            val = (leds_status>>1) & 0x1;
            up(&leds_lock);
            copy_to_user(buff, (const void *)&val, 1);
            break;
        }

        case 3: /* /dev/led3 */
        {
            down(&leds_lock);
            val = (leds_status>>2) & 0x1;
            up(&leds_lock);
            copy_to_user(buff, (const void *)&val, 1);
            break;
        }
    }
    return 1;
}




static ssize_t s3c24xx_leds_write(struct file *file, const char __user *buf, size_t count, loff_t * ppos)
{
    //int minor = MINOR(inode->i_rdev); //MINOR(inode->i_cdev);
    int minor = MINOR(file->f_dentry->d_inode->i_rdev);
    char val;

    copy_from_user(&val, buf, 1);

    switch (minor)
    {
        case 0: /* /dev/leds */
        {
            s3c2410_gpio_setpin(S3C2410_GPF4, (val & 0x1));
            s3c2410_gpio_setpin(S3C2410_GPF5, (val & 0x1));
            s3c2410_gpio_setpin(S3C2410_GPF6, (val & 0x1));
            down(&leds_lock);
            leds_status = val;
            up(&leds_lock);
            break;
        }

        case 1: /* /dev/led1 */
        {
            s3c2410_gpio_setpin(S3C2410_GPF4, val);

            if (val == 0)
            {
                down(&leds_lock);
                leds_status &= ~(1<<0);
                up(&leds_lock);
            }
            else
            {
                down(&leds_lock);
                leds_status |= (1<<0);
                up(&leds_lock);
            }
            break;
        }

        case 2: /* /dev/led2 */
        {
            s3c2410_gpio_setpin(S3C2410_GPF5, val);
            if (val == 0)
            {
                down(&leds_lock);
                leds_status &= ~(1<<1);
                up(&leds_lock);
            }
            else
            {
                down(&leds_lock);
                leds_status |= (1<<1);
                up(&leds_lock);
            }
            break;
        }

        case 3: /* /dev/led3 */
        {
            s3c2410_gpio_setpin(S3C2410_GPF6, val);
            if (val == 0)
            {
                down(&leds_lock);
                leds_status &= ~(1<<2);
                up(&leds_lock);
            }
            else
            {
                down(&leds_lock);
                leds_status |= (1<<2);
                up(&leds_lock);
            }
            break;
        }

    }

    return 1;
}



/* 这个结构是字符设备驱动程序的核心
 * 当应用程序操作设备文件时所调用的open、read、write等函数，
 * 最终会调用这个结构中指定的对应函数
 */
static struct file_operations s3c24xx_leds_fops = {
    .owner  =   THIS_MODULE,    /* 这是一个宏，推向编译模块时自动创建的__this_module变量 */
    .open   =   s3c24xx_leds_open,
    .read    =    s3c24xx_leds_read,
    .write    =    s3c24xx_leds_write,
};

/*
 * 执行insmod命令时就会调用这个函数
 */
static int __init s3c24xx_leds_init(void)
//static int __init init_module(void)

{
    int ret;
    int minor = 0;

    gpio_va = ioremap(0x56000000, 0x100000);
    if (!gpio_va) {
        return -EIO;
    }
    printk(DEVICE_NAME "gpio_va = %x\n",gpio_va);

    /* 注册字符设备
     * 参数为主设备号、设备名字、file_operations结构；
     * 这样，主设备号就和具体的file_operations结构联系起来了，
     * 操作主设备为LED_MAJOR的设备文件时，就会调用s3c24xx_leds_fops中的相关成员函数
     * LED_MAJOR可以设为0，表示由内核自动分配主设备号
     */
    ret = register_chrdev(LED_MAJOR, DEVICE_NAME, &s3c24xx_leds_fops);
    if (ret < 0) {
      printk(DEVICE_NAME " can‘t register major number\n");
      return ret;
    }
//oo00 :begin : 分配了四个子设备号  minor == 0 1 2 3
    leds_class = class_create(THIS_MODULE, "leds");
    if (IS_ERR(leds_class))
        return PTR_ERR(leds_class);

    leds_class_devs[0] = class_device_create(leds_class, NULL, MKDEV(LED_MAJOR, 0), NULL, "leds");

    for (minor = 1; minor < 4; minor++)
    {
        leds_class_devs[minor] = class_device_create(leds_class, NULL, MKDEV(LED_MAJOR, minor), NULL, "led%d", minor);
        if (unlikely(IS_ERR(leds_class_devs[minor])))
            return PTR_ERR(leds_class_devs[minor]);
    }
//oo00 :end

    printk(DEVICE_NAME " initialized\n");
    return 0;
}

/*
 * 执行rmmod命令时就会调用这个函数
 */
static void __exit s3c24xx_leds_exit(void)
{
    int minor;
    /* 卸载驱动程序 */
    unregister_chrdev(LED_MAJOR, DEVICE_NAME);

    for (minor = 0; minor < 4; minor++)
    {
        class_device_unregister(leds_class_devs[minor]);
    }
    class_destroy(leds_class);
    iounmap(gpio_va);
}

/* 这两行指定驱动程序的初始化函数和卸载函数 */
module_init(s3c24xx_leds_init);
module_exit(s3c24xx_leds_exit);

/* 描述驱动程序的一些信息，不是必须的 */
MODULE_AUTHOR("http://www.100ask.net");
MODULE_VERSION("0.1.0");
MODULE_DESCRIPTION("S3C2410/S3C2440 LED Driver");
MODULE_LICENSE("GPL");

#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <stdio.h>

/*
  *  ledtest <dev> <on|off>
  */

void print_usage(char *file)
{
    printf("Usage:\n");
    printf("%s <dev> <on|off>\n",file);
    printf("eg. \n");
    printf("%s /dev/leds on\n", file);
    printf("%s /dev/leds off\n", file);
    printf("%s /dev/led1 on\n", file);
    printf("%s /dev/led1 off\n", file);
}

int main(int argc, char **argv)
{
    int fd;
    char* filename;
    char val;

    if (argc != 3)
    {
        print_usage(argv[0]);
        return 0;
    }

    filename = argv[1];

    fd = open(filename, O_RDWR);
    if (fd < 0)
    {
        printf("error, can‘t open %s\n", filename);
        return 0;
    }

    if (!strcmp("on", argv[2]))
    {
        // 亮灯
        val = 0;
        write(fd, &val, 1);
    }
    else if (!strcmp("off", argv[2]))
    {
        // 灭灯
        val = 1;
        write(fd, &val, 1);
    }
    else
    {
        print_usage(argv[0]);
        return 0;
    }
    
    
    return 0;
}