标签：需要 aci ipvs ati conf tom check 虚拟主机 instance
# 节点分布情况
LVS主备上面，配置linux系统内核参数开启内核的路由模式 (同一网段 DR模式不需要)
modprobe ip_vs
vim /etc/sysctl.conf
net.ipv4.ip.forward = 1
LVS-dr-master
eth0: 192.168.146.141
LVS-dr-slave
eth0: 192.168.146.142
nginx1:
eth0: 192.168.146.139
nginx2:
eth0: 192.168.146.140
tomcat1:
eth0: 192.168.146.138 启用了4个tomcat
VIP: 192.168.146.200
# 拓扑如下所示
# 具体配置
### lvs master
### 1、安装ipvsadm、keepalived
|
1
|
yum install -y keepalived ipvsadm
|
### 2、使用keepalived来管理lvs
脚本：
|
global_defs
{
router_id master_210
}
vrrp_instance aiyou {
state MASTER
interface eth0
virtual_router_id 100 #这个数值 master和slave必须统一
priority 151 #这个数值决定哪台服务器是master
advert_int 1
authentication {
auth_type PASS
auth_pass 123456
}
virtual_ipaddress {
192.168.146.200
}
}
virtual_server 192.168.146.200 80 {
delay_loop 6
lb_algo wrr
lb_kind DR
# persistence_timeout 50
protocol TCP
real_server 192.168.146.139 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
real_server 192.168.146.140 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
}
|
### lvs slave
### 1、安装ipvsadm、keepalived
|
yum install -y keepalived ipvsadm
|
### 2、使用keepalived来管理lvs
|
global_defs
{
router_id slave_211
}
vrrp_instance aiyou {
state MASTER
interface eth0
virtual_router_id 100 #这个数值 master和slave必须统一
priority 150 #这个数值决定哪台服务器是master 这里我们比master数值低，所以角色是backup，
advert_int 1
authentication {
auth_type PASS
auth_pass 123456
}
virtual_ipaddress {
192.168.146.200
}
}
virtual_server 192.168.146.200 80 {
delay_loop 6
lb_algo wrr
lb_kind DR
# persistence_timeout 50
protocol TCP
real_server 192.168.146.139 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
real_server 192.168.146.140 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
}
|
### nginx1
### nginx上要跑个脚本
|
#!/bin/bash
#
# Script to start LVS DR real server.
# description: LVS DR real server
#
. /etc/rc.d/init.d/functions
VIP=192.168.146.200 #这里根据需要改成自己的VIP地址
host=`/bin/hostname`
case "$1" in
start)
# Start LVS-DR real server on this machine.
/sbin/ifconfig lo down
/sbin/ifconfig lo up
echo 1 > /proc/sys/net/ipv4/conf/lo/arp_ignore
echo 2 > /proc/sys/net/ipv4/conf/lo/arp_announce
echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore
echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce
/sbin/ifconfig lo:0 $VIP broadcast $VIP netmask 255.255.255.255 up
/sbin/route add -host $VIP dev lo:0
;;
stop)
# Stop LVS-DR real server loopback device(s).
/sbin/ifconfig lo:0 down
echo 0 > /proc/sys/net/ipv4/conf/lo/arp_ignore
echo 0 > /proc/sys/net/ipv4/conf/lo/arp_announce
echo 0 > /proc/sys/net/ipv4/conf/all/arp_ignore
echo 0 > /proc/sys/net/ipv4/conf/all/arp_announce
;;
status)
# Status of LVS-DR real server.
islothere=`/sbin/ifconfig lo:0 | grep $VIP`
isrothere=`netstat -rn | grep "lo:0" | grep $VIP`
if [ ! "$islothere" -o ! "isrothere" ];then
# Either the route or the lo:0 device
# not found.
echo "LVS-DR real server Stopped."
else
echo "LVS-DR real server Running."
fi
;;
*)
# Invalid entry.
echo "$0: Usage: $0 {start|status|stop}"
exit 1
;;
esac
|
### nginx2
### nginx上要跑个脚本
|
#!/bin/bash
#
# Script to start LVS DR real server.
# description: LVS DR real server
#
. /etc/rc.d/init.d/functions
VIP=192.168.146.200 #这里根据需要改成自己的VIP地址
host=`/bin/hostname`
case "$1" in
start)
# Start LVS-DR real server on this machine.
/sbin/ifconfig lo down
/sbin/ifconfig lo up
echo 1 > /proc/sys/net/ipv4/conf/lo/arp_ignore
echo 2 > /proc/sys/net/ipv4/conf/lo/arp_announce
echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore
echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce
/sbin/ifconfig lo:0 $VIP broadcast $VIP netmask 255.255.255.255 up
/sbin/route add -host $VIP dev lo:0
;;
stop)
# Stop LVS-DR real server loopback device(s).
/sbin/ifconfig lo:0 down
echo 0 > /proc/sys/net/ipv4/conf/lo/arp_ignore
echo 0 > /proc/sys/net/ipv4/conf/lo/arp_announce
echo 0 > /proc/sys/net/ipv4/conf/all/arp_ignore
echo 0 > /proc/sys/net/ipv4/conf/all/arp_announce
;;
status)
# Status of LVS-DR real server.
islothere=`/sbin/ifconfig lo:0 | grep $VIP`
isrothere=`netstat -rn | grep "lo:0" | grep $VIP`
if [ ! "$islothere" -o ! "isrothere" ];then
# Either the route or the lo:0 device
# not found.
echo "LVS-DR real server Stopped."
else
echo "LVS-DR real server Running."
fi
;;
*)
# Invalid entry.
echo "$0: Usage: $0 {start|status|stop}"
exit 1
;;
esac
|
### 后端tomcat安装省略
采用一机多实例模式（非多虚拟主机）
### 测试
### master上验证
|
[root@lvs1 ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 192.168.146.200:80 wrr
-> 192.168.146.139:80 Route 1 0 0
-> 192.168.146.140:80 Route 1 0 0
[root@lvs1 ~]#
|
### slave上验证
|
[root@lvs2 ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 192.168.146.200:80 wrr
-> 192.168.146.139:80 Route 1 0 0
-> 192.168.146.140:80 Route 1 0 0
[root@lvs2 ~]#
|
参考文章：
http://www.5ilinux.com/2014/05/lvs_keepalived_nginx_tomcat.html
标签：需要 aci ipvs ati conf tom check 虚拟主机 instance
原文地址：https://www.cnblogs.com/cheyunhua/p/10107890.html
