华为综合实验

标签：tin   link   intern   display   lte   VLAN间   注意   情况下   控制   

主动端与被动端
在静态LACP模式下，聚合组俩段的设备中，需要选择一端为主动端，而另外一端为被动端，通常情况下，LACP优先级较高的一端为主动端，如果优先级一样，那么就选MAC地址小的一端为主动端
三：实验拓扑图

ip自行配置
（1）sw4,sw5,sw6,sw7,sw3的vlan和trunk的配置：
这里用sw4为例：
[sw4]vlan batch 2 to 6 //创建2，3，4，5vlan
[sw4]int g0/0/1
[sw4-GigabitEthernet0/0/1]port link-type trunk //打开中继链路
[sw4-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[sw4-GigabitEthernet0/0/1]quit
[sw4]int g0/0/3
[sw4-GigabitEthernet0/0/3]port link-type access
[sw4-GigabitEthernet0/0/3]port default vlan 2
[sw4-GigabitEthernet0/0/3]quit
[sw4]int g0/0/2
[sw4-GigabitEthernet0/0/2]port link-type access
[sw4-GigabitEthernet0/0/2]port default vlan 3
[sw4-GigabitEthernet0/0/2]quit
查看vlan信息：display vlan
（2）sw1和sw2上vlan，trunk，lacp配置：
lacp配置(sw1)：
[sw1]lacp priority 1000
[sw1]int Eth-Trunk 12
[sw1-Eth-Trunk12]mode lacp-static
[sw1-Eth-Trunk12]load-balance dst-mac
[sw1-Eth-Trunk12]trunkport GigabitEthernet 0/0/23
[sw1-Eth-Trunk12]trunkport GigabitEthernet 0/0/24
[sw1-Eth-Trunk12]quit
（3）vlan间配置：
[sw1]vlan batch 2 to 9
[sw1]interface Eth-Trunk 12
[sw1-Eth-Trunk12]port link-type trunk
[sw1-Eth-Trunk12]port trunk allow-pass vlan all
[sw1-Eth-Trunk12]quit
[sw1]int g0/0/2
[sw1-GigabitEthernet0/0/2]port link-type trunk
[sw1-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[sw1-GigabitEthernet0/0/2]quit

[sw1]int g0/0/3
[sw1-GigabitEthernet0/0/3]port link-type trunk
[sw1-GigabitEthernet0/0/3]port trunk allow-pass vlan all
[sw1-GigabitEthernet0/0/3]quit

[sw1]int g0/0/1
[sw1-GigabitEthernet0/0/1]port link-type access
[sw1-GigabitEthernet0/0/1]port default vlan 7
[sw1-GigabitEthernet0/0/1]quit

interface Vlanif 2
ip address 192.168.2.1 255.255.255.0

interface Vlanif 3
ip address 192.168.3.1 255.255.255.0

interface Vlanif 4
ip address 192.168.4.1 255.255.255.0

interface Vlanif 7
ip address 192.168.7.1 255.255.255.0

（3）acp配置(sw2)：
[sw2]int Eth-Trunk 12
[sw2-Eth-Trunk12]mode lacp-static
[sw2-Eth-Trunk12]trunkport GigabitEthernet 0/0/23
[sw2-Eth-Trunk12]trunkport GigabitEthernet 0/0/24
[sw2-Eth-Trunk12]quit

vlan间配置：
[sw2]vlan batch 2 to 9
[sw2]interface Eth-Trunk 12
[sw2-Eth-Trunk12]port link-type trunk
[sw2-Eth-Trunk12]port trunk allow-pass vlan all
[sw2-Eth-Trunk12]quit

[sw2]int g0/0/2
[sw2-GigabitEthernet0/0/2]port link-type trunk
[sw2-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[sw2-GigabitEthernet0/0/2]quit

[sw2]int g0/0/3
[sw2-GigabitEthernet0/0/3]port link-type trunk
[sw2-GigabitEthernet0/0/3]port trunk allow-pass vlan all
[sw2-GigabitEthernet0/0/3]quit

[sw2]int g0/0/1
[sw2-GigabitEthernet0/0/1]port link-type access
[sw2-GigabitEthernet0/0/1]port default vlan 8
[sw2-GigabitEthernet0/0/1]quit

interface Vlanif 5
ip address 192.168.5.1 255.255.255.0

interface Vlanif 6
ip address 192.168.6.1 255.255.255.0

interface Vlanif 8
ip address 192.168.8.1 255.255.255.0

ospf 的配置：
分别在R2,SW1,SW2配置ospf
R2：
配置IP地址略
配置ospf：
[R2]ospf 110
[R2-ospf-110]area 0
[R2-ospf-110-area-0.0.0.0]network 192.168.7.0 0.0.0.255
[R2-ospf-110-area-0.0.0.0]network 192.168.8.0 0.0.0.255
[R2-ospf-110-area-0.0.0.0]quit
[R2-ospf-110]quit

SW1的OSPF配置
ospf 110
area 0
network 192.168.7.0 0.0.0.255
network 192.168.2.0 0.0.0.255
network 192.168.3.0 0.0.0.255
network 192.168.4.0 0.0.0.255
network 192.168.9.0 0.0.0.255
quit
quit

SW2的ospf配置：
ospf 110
area 0
network 192.168.8.0 0.0.0.255
network 192.168.9.0 0.0.0.255
network 192.168.5.0 0.0.0.255
network 192.168.6.0 0.0.0.255
quit
quit

查看ospf学习达到路由表：
display ospf routing

4、单臂路由配置
SW3配置：
[sw3]vlan batch 10 to 11
int g0/0/1
port link-type trunk
port trunk allow-pass vlan all
quit

int g0/0/2
port link-type access
port default vlan 10
quit

int g0/0/3
port link-type access
port default vlan 11
quit

R4的单臂路由配置：
int G0/0/0.10
dot1q termination vid 10
ip address 192.168.10.1 255.255.255.0
arp broadcast enable
int G0/0/0.11
dot1q termination vid 11
ip address 192.168.11.1 255.255.255.0
arp broadcast enable

5、Rip的配置
分别R2,R3,R4上配置rip：
如：R3
rip
undo summary
version 2
network 192.168.12.0
network 192.168.13.0

6、配置路由器重分发
在R2上配置：
[R2]ospf 110
[R2-ospf-110]import-route rip 1
[R2-ospf-110]rip
[R2-rip-1]import-route ospf 110
[R2-rip-1]quit

查看路由表： display ip routing-table
查看接口配置IP地址： display ip interface brief

7、配置NAT及访问控制
在R2上配置：
（1）配置默认路由去往internet
ip route-static 0.0.0.0 0.0.0.0 200.0.0.2

(2)默认路由重分发
[R2]ospf 110
[R2-ospf-110]default-route-advertise
[R2-ospf-110]quit

[R2]rip
[R2-rip-1]default-route originate
[R2-rip-1]quit

（3）配置PAT实现内网能访问internet
[R2]nat address-group 1 200.0.0.100 200.0.0.100
[R2]acl 2000
[R2-acl-basic-2000]rule 0 permit source any
[R2-acl-basic-2000]quit
[R2]int g3/0/0
[R2-GigabitEthernet3/0/0]nat outbound 2000 address-group 1
[R2-GigabitEthernet3/0/0]quit

(4)配置静态NAT，将2.10服务器发布到internet。
[R2] int g3/0/0
[R2-GigabitEthernet3/0/0]nat server global 200.0.0.200 inside 192.168.2.10
[R2-GigabitEthernet3/0/0]quit

(5)ACL控制192.168.10.0网段不能访问internet
acl 3000
rule 0 deny ip source 192.168.10.0 0.0.0.255 destination 200.0.0.0 0.0.0.255
rule 5 deny ip source 192.168.10.0 0.0.0.255 destination 201.0.0.0 0.0.0.255

[R2]int g0/0/2
[R2-GigabitEthernet0/0/2]traffic-filter inbound acl 3000
[R2-GigabitEthernet0/0/2]quit

查看NAT转换条目：display nat session all
查看ACL信息： display acl all
查看ospf邻居信息： display ospf peer brief

华为综合实验

标签：tin   link   intern   display   lte   VLAN间   注意   情况下   控制   

原文地址：https://blog.51cto.com/14400213/2443738