标签：启用 十进制 之间 ast cas tag 去掉 通过 mamicode
IPv6 手工tunnel和自动tunnel
同时请在R1和R4运行OSPFv3，R2连接R1的接口以及R3连接R4的接口运行OSPFv3，此步骤仅仅以R4为例，请自行完成其他：
R4(config)#ipv6 unicast-routing
R4(config)#int lo0
R4(config-if)#ip add 4.4.4.4 255.255.255.255
R4(config-if)#ipv6 address 2044::4/128
R4(config-if)#int e0/1
R4(config-if)#no shut
R4(config-if)#ipv6 address 2034::4/64
R4(config-if)#ipv6 ospf 1 area 0
R4#show ipv6 route ospf
IPv6 Routing Table - 8 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
O 2011::1/128 [110/11131]
via FE80::CE02:57FF:FE20:1, Ethernet0/1
O 2012::/64 [110/11131]
via FE80::CE02:57FF:FE20:1, Ethernet0/1
O 2023::/64 [110/22232]
via FE80::CE02:57FF:FE20:1, Ethernet0/1
R4#ping 2011::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2011::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 108/150/216 ms
3、自动tunnel（6to4 tunnel）
自动tunnel不支持动态路由协议，不能配置tunnel的Destination，所以去掉之前相关的配置
R3(config)#int tunnel 1
R3(config-if)#no ipv6 ospf 1 area 0
R3(config-if)#no tunnel destination
R3(config-if)#tunnel mode ipv6ip 6to4---把模式改为自动tunnel
接下来需要计算tunnel的地址，该地址以2002开始，接下来的32位是十进制的ipv4地址转换为16进制的IPv6地址,R2的tunnel的IPv6地址有22.1.1.1转换而来，那麽22=16,1=01,则转换后的地址为2002:1601:0101::/64;33.1.1.1转换完之后为33=21，则最终=2002:2101:101::/64
R3(config-if)#ipv6 address 2002:2101:101::3/64
由于不支持动态路由协议，我们来写一条静态去往2002：：/16位的前缀
R3(config)#ipv6 route 2002::/16 tunnel 1
！
R2的配置：
interface Tunnel1
no ip address
no ip redirects
ipv6 address 2002:1601:101::2/64
tunnel source Loopback0
tunnel mode ipv6ip 6to4
ipv6 route 2002::/16 tunnel 1
测试
R2#ping 2002:2101:101::3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2002:2101:101::3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/37/88 ms
查看tunnel的情况：
R2#show interfaces tunnel 1
Tunnel1 is up, line protocol is up
Hardware is Tunnel
MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 22.1.1.1 (Loopback0), destination UNKNOWN
Tunnel protocol/transport IPv6 6to4
Fast tunneling enabled
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
但是现在R1不能和R4通信，因为R1和R4没有对端的路由（有ospfv3的邻居）
R4#show ipv6 ospf neighbor
Neighbor ID Pri State Dead Time Interface ID Interface
33.1.1.1 1 FULL/DR 00:00:39 5 Ethernet0/1
R4#show ipv6 route
IPv6 Routing Table - 6 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
O 2033::3/128 [110/10]
via FE80::CE02:57FF:FE20:1, Ethernet0/1
C 2034::/64 [0/0]
via ::, Ethernet0/1
L 2034::4/128 [0/0]
via ::, Ethernet0/1
LC 2044::4/128 [0/0]
via ::, Loopback0
L FE80::/10 [0/0]
via ::, Null0
L FF00::/8 [0/0]
via ::, Null0
解决方案为在R2和R3上写默认路由，下一跳指向对端的隧道地址
R2(config)#ipv6 route ::/0 2002:2101:101::3
！
R3(config)#ipv6 route ::/0 2002:1601:101::2
如果采用OSPFv3，那么可以在R2和R3上产生一条默认路由
R3(config)#ipv6 router ospf 1
R3(config-rtr)#default-information originate always
!
R2(config)#ipv6 router ospf 1
R2(config-rtr)#default-information originate always
R4#show ipv6 route
IPv6 Routing Table - 7 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
OE2 ::/0 [110/1], tag 1
via FE80::CE02:57FF:FE20:1, Ethernet0/1
O 2033::3/128 [110/10]
via FE80::CE02:57FF:FE20:1, Ethernet0/1
C 2034::/64 [0/0]
via ::, Ethernet0/1
L 2034::4/128 [0/0]
via ::, Ethernet0/1
LC 2044::4/128 [0/0]
via ::, Loopback0
L FE80::/10 [0/0]
via ::, Null0
L FF00::/8 [0/0]
via ::, Null0
R4#ping 2011::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2011::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/66/132 ms
实验完成
标签：启用 十进制 之间 ast cas tag 去掉 通过 mamicode
原文地址：https://blog.51cto.com/enderjoe/2459074
