标签：des style http io color os ar for sp
U-Boot SPL 2014.04 (Oct 24 2014 - 16:39:49)
Board: Cubietruck
DRAM: 2048 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600
U-Boot 2014.04 (Oct 24 2014 - 16:39:49) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Board: Cubietruck
I2C: ready
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: dwmac.1c50000
Hit any key to stop autoboot: 0
reading uEnv.txt
240 bytes read in 16 ms (14.6 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
reading uImage
2540392 bytes read in 139 ms (17.4 MiB/s)
reading dtb
23026 bytes read in 28 ms (802.7 KiB/s)
## Booting kernel from Legacy Image at 46000000 ...
Image Name: ARM OpenWrt Linux-3.14.18
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2540328 Bytes = 2.4 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 49000000
Booting using the fdt blob at 0x49000000
Loading Kernel Image ... OK
Using Device Tree in place at 49000000, end 490089f1
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.18 (hades@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox/Linaro GCC 4.8-2014.04 svn-r173) ) #1 SMP PREEMPT Fri Oct 31 10:52:15 CST 2014
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Cubietech Cubietruck
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @ee7d6000 s7104 r8192 d13376 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522768
[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2074212K/2097152K available (3603K kernel code, 161K rwdata, 1016K rodata, 182K init, 602K bss, 22940K reserved, 1318912K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc048af04 (4620 kB)
[ 0.000000] .init : 0xc048b000 - 0xc04b8bc0 ( 183 kB)
[ 0.000000] .data : 0xc04ba000 - 0xc04e2660 ( 162 kB)
[ 0.000000] .bss : 0xc04e2660 - 0xc057921c ( 603 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000025] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[ 0.000182] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[ 0.000353] Console: colour dummy device 80x30
[ 0.000391] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448)
[ 0.060082] pid_max: default: 32768 minimum: 301
[ 0.060263] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060277] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.065952] CPU: Testing write buffer coherency: ok
[ 0.066305] /cpus/cpu@0 missing clock-frequency property
[ 0.066324] /cpus/cpu@1 missing clock-frequency property
[ 0.066338] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.066365] Setting up static identity map for 0x400118a8 - 0x400118dc
[ 0.120543] CPU1: failed to boot: -38
[ 0.120573] Brought up 1 CPUs
[ 0.120580] SMP: Total of 1 processors activated.
[ 0.120587] CPU: All CPU(s) started in SVC mode.
[ 0.125357] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.125695] pinctrl core: initialized pinctrl subsystem
[ 0.126074] regulator-dummy: no parameters
[ 0.126384] NET: Registered protocol family 16
[ 0.126651] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.135931] bio: create slab <bio-0> at 0
[ 0.136570] reg-fixed-voltage ahci-5v.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
[ 0.136599] platform ahci-5v.3: Driver reg-fixed-voltage requests probe deferral
[ 0.136626] reg-fixed-voltage usb1-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[ 0.136641] platform usb1-vbus.4: Driver reg-fixed-voltage requests probe deferral
[ 0.136663] reg-fixed-voltage usb2-vbus.5: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[ 0.136677] platform usb2-vbus.5: Driver reg-fixed-voltage requests probe deferral
[ 0.136700] reg-fixed-voltage vmmc3.7: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/vmmc3_pin@0, deferring probe
[ 0.136714] platform vmmc3.7: Driver reg-fixed-voltage requests probe deferral
[ 0.137104] SCSI subsystem initialized
[ 0.137619] usbcore: registered new interface driver usbfs
[ 0.137682] usbcore: registered new interface driver hub
[ 0.137810] usbcore: registered new device driver usb
[ 0.137920] pps_core: LinuxPPS API ver. 1 registered
[ 0.137929] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.137953] PTP clock support registered
[ 0.138835] Switched to clocksource timer
[ 0.140356] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.140374] Could not switch to high resolution mode on CPU 0
[ 0.145804] NET: Registered protocol family 2
[ 0.146796] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.146887] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.147009] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.147085] TCP: reno registered
[ 0.147104] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.147160] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.147475] NET: Registered protocol family 1
[ 0.148789] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.148892] audit: initializing netlink subsys (disabled)
[ 0.148957] audit: type=2000 audit(0.130:1): initialized
[ 0.149546] bounce pool size: 64 pages
[ 0.157343] VFS: Disk quotas dquot_6.5.2
[ 0.157678] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.159595] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.159609] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.160560] msgmni has been set to 1475
[ 0.162412] io scheduler noop registered
[ 0.162431] io scheduler deadline registered
[ 0.162474] io scheduler cfq registered (default)
[ 0.162755] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
[ 0.165008] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.206550] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.229025] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[ 0.810025] console [ttyS0] enabled
[ 0.834442] 1c28800.serial: ttyS1 at MMIO 0x1c28800 (irq = 35, base_baud = 1500000) is a U6_16550A
[ 0.844334] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral
[ 0.853056] stmmaceth 1c50000.ethernet: no regulator found
[ 0.858602] stmmaceth 1c50000.ethernet: no reset control found
[ 0.864479] Ring mode enabled
[ 0.867533] No HW DMA feature register supported
[ 0.872069] Normal descriptors
[ 0.875391] TX Checksum insertion supported
[ 0.883818] libphy: stmmac: probed
[ 0.887230] eth0: PHY ID 001cc915 at 0 IRQ 0 (stmmac-0:00) active
[ 0.893404] eth0: PHY ID 001cc915 at 1 IRQ 0 (stmmac-0:01)
[ 0.898996] ehci_hcd: USB 2.0 ‘Enhanced‘ Host Controller (EHCI) Driver
[ 0.905561] ehci-platform: EHCI generic platform driver
[ 0.911004] platform 1c14000.usb: Driver ehci-platform requests probe deferral
[ 0.918300] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
[ 0.925749] usbcore: registered new interface driver usb-storage
[ 0.932083] mousedev: PS/2 mouse device common for all mice
[ 0.939319] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 0.948156] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225.
[ 0.953398] sunxi-mmc 1c0f000.mmc: base:0xf00f4000 irq:64
[ 0.959282] platform 1c12000.mmc: Driver sunxi-mmc requests probe deferral
[ 0.967458] sunxi-ss 1c15000.crypto-engine: Die ID 0
[ 0.974014] TCP: cubic registered
[ 0.977335] Initializing XFRM netlink socket
[ 0.981712] NET: Registered protocol family 17
[ 0.986255] 8021q: 802.1Q VLAN Support v1.8
[ 0.990594] Registering SWP/SWPB emulation handler
[ 0.995773] registered taskstats version 1
[ 0.999915] regulator-dummy: disabling
[ 1.004262] ahci-5v: 5000 mV
[ 1.007679] usb1-vbus: 5000 mV
[ 1.011246] usb2-vbus: 5000 mV
[ 1.014705] vmmc3: 3300 mV
[ 1.080370] ahci-sunxi 1c18000.sata: controller can‘t do PMP, turning off CAP_PMP
[ 1.087858] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 1.093773] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.102752] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 1.113723] scsi0 : ahci_platform
[ 1.117392] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[ 1.125699] ehci-platform 1c14000.usb: EHCI Host Controller
[ 1.131464] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[ 1.139311] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000
[ 1.160354] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 1.166635] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.174469] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.181721] usb usb1: Product: EHCI Host Controller
[ 1.186614] usb usb1: Manufacturer: Linux 3.14.18 ehci_hcd
[ 1.192123] usb usb1: SerialNumber: 1c14000.usb
[ 1.197204] hub 1-0:1.0: USB hub found
[ 1.201042] hub 1-0:1.0: 1 port detected
[ 1.205618] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 1.211251] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[ 1.219084] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000
[ 1.240329] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 1.246595] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.253397] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.260622] usb usb2: Product: EHCI Host Controller
[ 1.265495] usb usb2: Manufacturer: Linux 3.14.18 ehci_hcd
[ 1.272008] usb usb2: SerialNumber: 1c1c000.usb
[ 1.278065] hub 2-0:1.0: USB hub found
[ 1.281874] hub 2-0:1.0: 1 port detected
[ 1.287005] sunxi-mmc 1c12000.mmc: base:0xf0138000 irq:67
[ 1.367213] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 1.480342] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.500427] Waiting for root device /dev/mmcblk0p2...
[ 1.570328] mmc0: new high speed SDXC card at address 59b4
[ 1.576432] mmcblk0: mmc0:59b4 SD64G 59.0 GiB
[ 1.582402] mmcblk0: p1 p2
[ 1.612139] EXT4-fs (mmcblk0p2): couldn‘t mount as ext3 due to feature incompatibilities
[ 1.621265] EXT4-fs (mmcblk0p2): couldn‘t mount as ext2 due to feature incompatibilities
[ 1.651677] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.659823] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.666930] Freeing unused kernel memory: 180K (c048b000 - c04b8000)
[ 1.676068] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 1.689188] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.18 #1
[ 1.695186] Backtrace:
[ 1.697665] [<c001a2a0>] (dump_backtrace) from [<c001a584>] (show_stack+0x18/0x1c)
[ 1.705222] r6:00000000 r5:ee082008 r4:c04ce83c r3:00000000
[ 1.710934] [<c001a56c>] (show_stack) from [<c01b8030>] (dump_stack+0xa0/0xd8)
[ 1.718153] [<c01b7f90>] (dump_stack) from [<c0023400>] (panic+0xb4/0x200)
[ 1.725016] r6:00000000 r5:c000cb48 r4:c041ee60 r3:00000001
[ 1.730726] [<c0023350>] (panic) from [<c000cc44>] (kernel_init+0xfc/0x104)
[ 1.737677] r3:c04bd080 r2:c04bac54 r1:2e31f000 r0:c041ee60
[ 1.743377] r7:00000000
[ 1.745924] [<c000cb48>] (kernel_init) from [<c0008d78>] (ret_from_fork+0x14/0x3c)
[ 1.753480] r4:00000000 r3:ee082000
标签：des style http io color os ar for sp
原文地址：http://my.oschina.net/tiancheng13/blog/339268
