uart串口通信

//串口接收模块
module uart_byte_tx(
    Clk,
    Rst_n,
    data_byte,
    send_en,
    baud_set,
    
    Rs232_Tx,
    Tx_Done,
    uart_state
);

    input Clk;
    input Rst_n;
    input [7:0]data_byte;
    input send_en;                    //发送标志信号位
    input [2:0]baud_set;            //波特率设定
    
    output reg Rs232_Tx;
    output reg Tx_Done;                //串口发送完成标志
    output reg uart_state;                
    
    reg bps_clk;    //波特率时钟周期
    
    reg [15:0]div_cnt;//分频计数器：每计数满一轮，即计数满一个波特率周期，
                      //  即div_cnt = bps_DR 时该寄存器则清零重新计数
    
    reg [15:0]bps_DR;//分频计数最大值：可方便随时更换发送波特率
    
    reg [3:0]bps_cnt;//波特率时钟周期计数器：用于判断此时该发送到第几位数据
    
    reg [7:0]r_data_byte;   //发送的数据寄存器
    
    localparam START_BIT = 1‘b0;
    localparam STOP_BIT = 1‘b1;
    
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        uart_state <= 1‘b0;
    else if(send_en)
        uart_state <= 1‘b1;
    else if(bps_cnt == 4‘d11)
        uart_state <= 1‘b0;
    else
        uart_state <= uart_state;
    
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        r_data_byte <= 8‘d0;
    else if(send_en)
        r_data_byte <= data_byte;
    else
        r_data_byte <= r_data_byte;
    
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        bps_DR <= 16‘d5207;
    else begin
        case(baud_set)                //不同波特率所对应的分频计数最大值
            0:bps_DR <= 16‘d5207;
            1:bps_DR <= 16‘d2603;
            2:bps_DR <= 16‘d1301;
            3:bps_DR <= 16‘d867;
            4:bps_DR <= 16‘d433;
            default:bps_DR <= 16‘d5207;            
        endcase
    end    
    
    //counter
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        div_cnt <= 16‘d0;
    else if(uart_state)begin
        if(div_cnt == bps_DR)
            div_cnt <= 16‘d0;
        else
            div_cnt <= div_cnt + 1‘b1;
    end
    else
        div_cnt <= 16‘d0;
    
    // bps_clk gen
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        bps_clk <= 1‘b0;
    else if(div_cnt == 16‘d1)
        bps_clk <= 1‘b1;
    else
        bps_clk <= 1‘b0;
    
    //bps counter
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)    
        bps_cnt <= 4‘d0;
    else if(bps_cnt == 4‘d11)
        bps_cnt <= 4‘d0;
    else if(bps_clk)
        bps_cnt <= bps_cnt + 1‘b1;
    else
        bps_cnt <= bps_cnt;
        
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        Tx_Done <= 1‘b0;
    else if(bps_cnt == 4‘d11)
        Tx_Done <= 1‘b1;
    else
        Tx_Done <= 1‘b0;
        
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        Rs232_Tx <= 1‘b1;
    else begin
        case(bps_cnt)                    //注意：在一个波特率周期里是一直在发送数据
            0:Rs232_Tx <= 1‘b1;            //bps_cnt的值会持续一个波特率周期才会改变
            1:Rs232_Tx <= START_BIT;    //一个波特率周期 = 发送一个bit位数据的时间 
            2:Rs232_Tx <= r_data_byte[0];
            3:Rs232_Tx <= r_data_byte[1];
            4:Rs232_Tx <= r_data_byte[2];
            5:Rs232_Tx <= r_data_byte[3];
            6:Rs232_Tx <= r_data_byte[4];
            7:Rs232_Tx <= r_data_byte[5];
            8:Rs232_Tx <= r_data_byte[6];
            9:Rs232_Tx <= r_data_byte[7];
            10:Rs232_Tx <= STOP_BIT;
            default:Rs232_Tx <= 1‘b1;
        endcase
    end    

endmodule

//串口接收模块
module uart_byte_rx(
    Clk,
    Rst_n,
    baud_set,
    Rs232_Rx,
    
    data_byte,
    Rx_Done
);

    input Clk;
    input Rst_n;
    input [2:0]baud_set;
    input Rs232_Rx;
    
    output reg [7:0]data_byte;
    output reg Rx_Done;
    
    reg s0_Rs232_Rx,s1_Rs232_Rx;//同步寄存器
    
    reg tmp0_Rs232_Rx,tmp1_Rs232_Rx;//数据寄存器
    
    reg [15:0]bps_DR;//分频计数器计数最大值
    reg [15:0]div_cnt;//分频计数器
    reg bps_clk;//
    reg [7:0]bps_cnt;
    
    reg uart_state;
    
    reg [2:0] r_data_byte [7:0];        //定义8个位宽为3的寄存器
    reg [7:0] tmp_data_byte;            
    reg [2:0] START_BIT,STOP_BIT;        //起始位和停止位
    
    wire nedege;
    
    //同步寄存器，消除亚稳态
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)begin
        s0_Rs232_Rx <= 1‘b0;
        s1_Rs232_Rx <= 1‘b0;    
    end
    else begin
        s0_Rs232_Rx <= Rs232_Rx;
        s1_Rs232_Rx <= s0_Rs232_Rx;    
    end
    
    //数据寄存器
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)begin
        tmp0_Rs232_Rx <= 1‘b0;
        tmp1_Rs232_Rx <= 1‘b0;    
    end
    else begin
        tmp0_Rs232_Rx <= s1_Rs232_Rx;
        tmp1_Rs232_Rx <= tmp0_Rs232_Rx;    
    end
    
    assign nedege = !tmp0_Rs232_Rx & tmp1_Rs232_Rx;
    
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        bps_DR <= 16‘d324;
    else begin
        case(baud_set)
            0:bps_DR <= 16‘d324;
            1:bps_DR <= 16‘d162;
            2:bps_DR <= 16‘d80;
            3:bps_DR <= 16‘d53;
            4:bps_DR <= 16‘d26;
            default:bps_DR <= 16‘d324;            
        endcase
    end
    
    //counter
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        div_cnt <= 16‘d0;
    else if(uart_state)begin
        if(div_cnt == bps_DR)
            div_cnt <= 16‘d0;
        else
            div_cnt <= div_cnt + 1‘b1;
    end
    else
        div_cnt <= 16‘d0;
        
    // bps_clk gen
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        bps_clk <= 1‘b0;
    else if(div_cnt == 16‘d1)
        bps_clk <= 1‘b1;
    else
        bps_clk <= 1‘b0;
    
    //bps counter
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)    
        bps_cnt <= 8‘d0;
    else if(bps_cnt == 8‘d159 | (bps_cnt == 8‘d12 && (START_BIT > 2)))
        bps_cnt <= 8‘d0;
    else if(bps_clk)
        bps_cnt <= bps_cnt + 1‘b1;
    else
        bps_cnt <= bps_cnt;

    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        Rx_Done <= 1‘b0;
    else if(bps_cnt == 8‘d159)
        Rx_Done <= 1‘b1;
    else
        Rx_Done <= 1‘b0;
        
//    always@(posedge Clk or negedge Rst_n)
//    if(!Rst_n)
//        data_byte <= 8‘d0;
//    else if(bps_cnt == 8‘d159)
//        data_byte <= tmp_data_byte;
//    else
//        data_byte <= data_byte;
        
        
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        data_byte <= 8‘d0;
    else if(bps_cnt == 8‘d159)begin
        data_byte[0] <= r_data_byte[0][2];  //r_data_byte[0]寄存器位宽为3，  000=0 ， 001=1 ，010=2 ，011=3  
        data_byte[1] <= r_data_byte[1][2];                                //     100=4 ， 101=5 ，110=6    ，111=7    
        data_byte[2] <= r_data_byte[2][2];    //可以发现当r_data_byte[0]寄存器的值>3时，data_byte[0]寄存器所接收的值为1，    
        data_byte[3] <= r_data_byte[3][2];    //而r_data_byte[0][2]的值恰好都=1。所以此处取r_data_byte[0]寄存器的的二位值作为接收到的有效数据    
        data_byte[4] <= r_data_byte[4][2];        
        data_byte[5] <= r_data_byte[5][2];        
        data_byte[6] <= r_data_byte[6][2];
        data_byte[7] <= r_data_byte[7][2];
    end    
        
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)begin
        START_BIT = 3‘d0;
        r_data_byte[0] <= 3‘d0;
        r_data_byte[1] <= 3‘d0;
        r_data_byte[2] <= 3‘d0;
        r_data_byte[3] <= 3‘d0;
        r_data_byte[4] <= 3‘d0;
        r_data_byte[5] <= 3‘d0;
        r_data_byte[6] <= 3‘d0;
        r_data_byte[7] <= 3‘d0;
        STOP_BIT = 3‘d0;
    end
    else if(bps_clk)begin
        case(bps_cnt)
            0:begin
                    START_BIT = 3‘d0;
                    r_data_byte[0] <= 3‘d0;
                    r_data_byte[1] <= 3‘d0;
                    r_data_byte[2] <= 3‘d0;
                    r_data_byte[3] <= 3‘d0;
                    r_data_byte[4] <= 3‘d0;
                    r_data_byte[5] <= 3‘d0;
                    r_data_byte[6] <= 3‘d0;
                    r_data_byte[7] <= 3‘d0;
                    STOP_BIT = 3‘d0;            
                end                        //用序列机的方法接收数据，并且采样6次数据的值累加存在r_data_byte寄存器
            6,7,8,9,10,11:START_BIT <= START_BIT + s1_Rs232_Rx;
            22,23,24,25,26,27:r_data_byte[0] <= r_data_byte[0] + s1_Rs232_Rx;        //采样6次数据，如果6次数据的和大于3，则表示所采集的该bit位的数据位1，
            38,39,40,41,42,43:r_data_byte[1] <= r_data_byte[1] + s1_Rs232_Rx;        //如果如果6次数据的和小于3，则表示所采集的该bit位的数据位0，
            54,55,56,57,58,59:r_data_byte[2] <= r_data_byte[2] + s1_Rs232_Rx;        //如果如果6次数据的和等于3，则表示所采集的该bit位的数据位无效，
            70,71,72,73,74,75:r_data_byte[3] <= r_data_byte[3] + s1_Rs232_Rx;
            86,87,88,89,90,91:r_data_byte[4] <= r_data_byte[4] + s1_Rs232_Rx;
            102,103,104,105,106,107:r_data_byte[5] <= r_data_byte[5] + s1_Rs232_Rx;
            118,119,120,121,122,123:r_data_byte[6] <= r_data_byte[6] + s1_Rs232_Rx;
            134,135,136,137,138,139:r_data_byte[7] <= r_data_byte[7] + s1_Rs232_Rx;
            150,151,152,153,154,155:STOP_BIT <= STOP_BIT + s1_Rs232_Rx;
            default:
                begin
                    START_BIT = START_BIT;
                    r_data_byte[0] <= r_data_byte[0];
                    r_data_byte[1] <= r_data_byte[1];
                    r_data_byte[2] <= r_data_byte[2];
                    r_data_byte[3] <= r_data_byte[3];
                    r_data_byte[4] <= r_data_byte[4];
                    r_data_byte[5] <= r_data_byte[5];
                    r_data_byte[6] <= r_data_byte[6];
                    r_data_byte[7] <= r_data_byte[7];
                    STOP_BIT = STOP_BIT;                        
                end
        endcase
    end
    
    always@(posedge Clk or negedge Rst_n)
    if(!Rst_n)
        uart_state <= 1‘b0;
    else if(nedege)
        uart_state <= 1‘b1;
    else if(Rx_Done || (bps_cnt == 8‘d12 && (START_BIT > 2)))
        uart_state <= 1‘b0;
    else
        uart_state <= uart_state;        

endmodule