标签:拓扑图 loop bit dynamic 区域 hosts 并且 current 协议
ISIS在IPV6中的应用拓扑图拓扑图
?实验目的:
熟练掌握IPV6与IPV4的在ISIS协议下各种模式如何使用,并且能根据实验要求完成各项指标。
实验要求
1.各个相连链路的接口ipv4地址按:XY.1.1.X/Y--/24位掩码的方式配置,各路由器的环回口地址按:X.X.X.X/32形式配置。
2.各个相连链路的接口ipv6地址按:2001:XY::X/Y--/64位掩码的方式配置,各路由器的环回口地址按:2002::X/Y--/128位的方式配置。
3.R1配置在47.0123的区域内,R2.R3,R4 配置在47.0234区域内,各路由器的系统ID按:XXXX.XXXX.XXXX.或者YYYY.YYYY.YYYY的形式配置
4.R1配置在ISIS Level-2的级别,R2.R3配置在ISIS Level-1-2的级别,R4配置在ISIS Level-1的级别。
5.通过修改R4接口下COST值的方式,使得IPV4到达R1的路由走R3,IPV6 的路由走R2.
实验步骤:
1.配置各路由器的相连接口的IP地址
2.配置各路由器的ISIS进程
3.配置各路由器接口下开启isis进程
具体配置:
#R1 的配置
[AR1]sysname R1
[R1]ipv6 // 在路由器上开启ipv6功能
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 12.1.1.1 255.255.255.0
[R1-GigabitErhernet0/0/0]ipv6 enable
[R1-GigabitEthernet0/0/0]ipv6 address 2001:12::1 64 //配置ipv6的地址
[R1-GigabitEthernet0/0/0]isis enable
[R1-GigabitEthernet0/0/0]isis ipv 6 enable
[R1-GigabitEthernet0/0/0]quit
[R1]interface GigabitEthernet0/0/1
[R1-GigabitEthernet0/0/1]ip address 13.1.1.1 255.255.255.0
[R1-GigabitEthernet0/0/1]ipv6 enable
[R1-GigabitEthernet0/0/1]ipv6 address 2001:13::2 64
[R1-GigabitEthernet0/0/1]isis enable
[R1-GigabitEthernet0/0/1]isis ipv6 enable
[R1-GigabitEthernet0/0/1]quit
[R1]interface Loopback0
[R1-Loopback0]ip address 1.1.1.1 255.255.255.255
[R1-Loopback0]ipv6 enable //接口下开启IPV6功能
[R1-Loopback0]ipv6 address 2002::1 128 //配置IPV6地址
[R1-Loopback0]isis enable //在该接口下的IP地址宣告进ipv4的ISIS进程下
[R1-Loopback0]isis ipv6 enable //将该接口下的IP地址宣告进IPV6的ISIS进程中
[R1-Loopback0]quit
[R1]isis 1 //开启ISIS进程
[R1-isis-1] network-entity 47.0123.1111.1111.1111.00 //配置ISIS的区域ID和系统ID
[R1-isis-1]is-level level-2 //配置路由的ISIS级别为Level-2
[R1-isis-1]isis ipv6 enable standed //开启IPV6的标准模式
[R1-isis-1]quit
[R1]
#R2的配置
[AR2]sysname R2
[R2]ipv6
[R2]interface GigabitEthernet0/0/0
[R2-GigabitEthernet0/0/0]ip address 12.1.1.2 255.255.255.0
[R2-GigabitEthernet0/0/0]ipv6 enable
[R2-GigabitEthernet0/0/0]ipv6 address 2001:12::2 64
[R2-GigabitEthernet0/0/0]isis enable
[R2-GigabitEthernet0/0/0]isis ipv6 enable
[R2-GigabitEthernet0/0/0]quit
[R2]interface GigabitEthernet0/0/1
[R2-GigabitEthernet0/0/1]ip address 23.1.1.2 255.255.255.0
[R2-GigabitEtherne0/0/1]ipv6 enable
[R2-GigabitEthernet0/0/1]ipv6 adress 2001:23::2 64
[R2-GigabitEthernet0/0/1]isis enable
[R2-GigabitEthernet0/0/1]isis ipv6 enable
[R2-GigabitEthernet0/0/1]quit
[R2]interface GigabitEthernet0/0/2
[R2-GigabitEthernet0/0/2]ip address 24.1.1.2 255.255.255.0
[R2-GigabitEthernet0/0/2]ipv6 enable
[R2-Gigabit Ethernet0/0/2]ipv6 address 2001:24::2 64
[R2-GigabitEthernet0/0/2]isis enable
[R2-GigabitEthernet0/0/2]isis ipv6 enable
[R2-GigabitEthernet0/0/2]quit
[R2]interface loopback0
[R2-Loopback0]ip addrss 2.2.2.2 255.255.255.255
[R2-Loopback0]ipv6 enable
[R2-Loopback0]ipv6 address 2002::2 128
[R2-Loopback0]isis enable
[R2-Loopback0]isis ipv6 enable
[R2-Loopback0]quit
[R2]isis 1 //开启ISIS进程
[R2-isis-1] network-entity 47.0234.2222.2222.2222.00 //配置ISIS的区域ID和系统ID
[R2-isis-1]is-level level-2 //配置路由的ISIS级别为Level-2
[R2-isis-1]isis ipv6 enable standed //开启IPV6的标准模式
[R2-isis-1]quit
[R2]
#R3的配置
[AR3]sysname R3
[R3]ipv6
[R3]interface GigabitEthernet0/0/0
[R3-GigabitEthernet0/0/0]ip address 23.1.1.3 255.255.255.0
[R3-GigabitEthernet0/0/0]ipv6 enable
[R3-GigabitEthernet0/0/0]ipv6 address 2001:23::3 64
[R3-GigabitEthernet0/0/0]isis enable
[R3-GigabitEthernet0/0/0]isis ipv6 enable
[R3-GigabitEthernet0/0/0]quit
[R3]interface GigabitEthernet0/0/1
[R3-GigabitEthernet0/0/1]ip address 13.1.1.3 255.255.255.0
[R3-GigabitEtherne0/0/1]ipv6 enable
[R3-GigabitEthernet0/0/1]ipv6 adress 2001:13::3 64
[R3-GigabitEthernet0/0/1]isis enable
[R3-GigabitEthernet0/0/1]isis ipv6 enable
[R3-GigabitEthernet0/0/1]quit
[R3]interface GigabitEthernet0/0/2
[R3-GigabitEthernet0/0/2]ip address 34.1.1.3 255.255.255.0
[R3-GigabitEthernet0/0/2]ipv6 enable
[R3-Gigabit Ethernet0/0/2]ipv6 address 2001:34::3 64
[R3-GigabitEthernet0/0/2]isis enable
[R3-GigabitEthernet0/0/2]isis ipv6 enable
[R3-GigabitEthernet0/0/2]quit
[R3]interface loopback0
[R3-Loopback0]ip addrss 3.3.3.3 255.255.255.255
[R3-Loopback0]ipv6 enable
[R3-Loopback0]ipv6 address 2002::3 128
[R3-Loopback0]isis enable
[R3-Loopback0]isis ipv6 enable
[R3-Loopback0]quit
[R3]isis 1 //开启ISIS进程
[R3-isis-1] network-entity 47.0234.3333.3333.3333.00 //配置ISIS的区域ID和系统ID
[R3-isis-1]is-level level-2 //配置路由的ISIS级别为Level-2
[R3-isis-1]isis ipv6 enable standed //开启IPV6的标准模式
[R3-isis-1]quit
[R3]
#R4的配置
[AR4]sysname R4
[R4]ipv6 // 在路由器上开启ipv6功能
[R4]interface GigabitEthernet 0/0/0
[R4-GigabitEthernet0/0/2]ip address 24.1.1.4 255.255.255.0
[R4-GigabitErhernet0/0/2]ipv6 enable
[R4-GigabitEthernet0/0/2]ipv6 address 2001:24::4 64 //配置ipv6的地址
[R4-GigabitEthernet0/0/2]isis enable
[R4-GigabitEthernet0/0/2]isis ipv 6 enable
[R4-GigabitEthernet0/0/2]isis ipv6 cost 5 //在接口下修改IPV6的cost值
[R4-GigabitEthernet0/0/2]quit
[R4]interface GigabitEthernet0/0/1
[R4-GigabitEthernet0/0/1]ip address 34.1.1.4 255.255.255.0
[R4-GigabitEthernet0/0/1]ipv6 enable
[R4-GigabitEthernet0/0/1]ipv6 address 2001:34::4 64
[R4-GigabitEthernet0/0/1]isis enable
[R4-GigabitEthernet0/0/1]isis ipv6 enable
[R4-GigabitEthernet0/0/2]isis cost 5 //在接口下修改IPV4的cost值
[R4-GigabitEthernet0/0/1]quit
[R4]interface Loopback0
[R4-Loopback0]ip address 4.4.4.4 255.255.255.255
[R4-Loopback0]ipv6 enable //接口下开启IPV6功能
[R4-Loopback0]ipv6 address 2002::4 128 //配置IPV6地址
[R4-Loopback0]isis enable //在该接口下的IP地址宣告进ipv4的ISIS进程下
[R4-Loopback0]quit
[R4]isis 1 //开启ISIS进程
[R4-isis-1] network-entity 47.0234.4444.4444.4444.00 //配置ISIS的区域ID和系统ID
[R4-isis-1]is-level level-2 //配置路由的ISIS级别为Level-2
[R4-isis-1]isis ipv6 enable standed //开启IPV6的标准模式
[R4-isis-1]quit
[R4]
验证结果:
#R4上查看IPV6接口配置
[R4]display ipv6 interface //显示接口下IPV6的地址配置
GigabitEthernet0/0/1 current state : UP //接口物理状态UP
IPv6 protocol current state : UP //接口协议状态:UP
IPv6 is enabled, link-local address is FE80::2E0:FCFF:FE88:411 //接口链路本地地址
Global unicast address(es): //接口全局单播地址
2001:34::4, subnet is 2001:34::/64 //ipv6 地址以及前缀信息
Joined group address(es): //加入的组播组
FF02::1:FF00:4 //请求节点组播地址
FF02::2 //本地链路上所有节点的组播地址
FF02::1 //本地链路上所有路由器的组播地址
FF02::1:FF88:411 //链路本地地址组播组
MTU is 1500 bytes
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
ND retransmit interval is 1000 milliseconds
Hosts use stateless autoconfig for addresses
GigabitEthernet0/0/2 current state : UP
IPv6 protocol current state : UP
IPv6 is enabled, link-local address is FE80::2E0:FCFF:FE88:412
Global unicast address(es):
2001:24::4, subnet is 2001:24::/64
Joined group address(es):
FF02::1:FF00:4
FF02::2
FF02::1
FF02::1:FF88:412
MTU is 1500 bytes
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
ND retransmit interval is 1000 milliseconds
Hosts use stateless autoconfig for addresses
LoopBack0 current state : UP
Line protocol current state : UP (spoofing)
IPv6 is enabled, link-local address is FE80::800:0
Global unicast address(es):
2002::4, subnet is 2002::4/128
Joined group address(es):
FF02::1:FF00:4
FF02::2
FF02::1
FF02::1:FF00:0
MTU is 1500 bytes
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
ND retransmit interval is 1000 milliseconds
Hosts use stateless autoconfig for addresses
[R4]
#R4的Gigabit Ethernet0/0/2的详细信息:
[R4]display isis interface GigabitEthernet 0/0/2 verbose
Interface information for ISIS(1)
Interface id IPV4.State IPV6.State MTU Type DIS
GE0/0/2 002 Up Up 1497 L1/L2 Yes/No
Circuit MT State : Standard
Description : HUAWEI, AR Series, GigabitEthernet0/0/2 Interface
SNPA Address : 00e0-fc88-0412
IP Address : 24.1.1.4
IPV6 Link Local Address : FE80::2E0:FCFF:FE88:412
IPV6 Global Address(es) : 2001:24::4/64
Csnp Timer Value : L1 10 L2 10
Hello Timer Value : L1 10 L2 10
DIS Hello Timer Value : L1 3 L2 3
Hello Multiplier Value : L1 3 L2 3
LSP-Throttle Timer : L12 50
Cost : L1 10 L2 10
Ipv6 Cost : L1 50 L2 50
Priority : L1 64 L2 64
Retransmit Timer Value : L12 5
Bandwidth-Value : Low 1000000000 High 0
Static Bfd : NO
Dynamic Bfd : NO
Fast-Sense Rpr : NO
[R4]
标签:拓扑图 loop bit dynamic 区域 hosts 并且 current 协议
原文地址:https://blog.51cto.com/dfsshan/2483270