码迷,mamicode.com
首页 > 其他好文 > 详细

链路捆绑实现冗余功能实验

时间:2020-05-20 14:07:27      阅读:62      评论:0      收藏:0      [点我收藏+]

标签:oop   rtp   bpdu   port   image   ddr   路由器   toc   ports   

1.在华为模拟器ensp上设置两个普通路由器,两个交换机,两台PC
先打开ensp ,新建2个路由器和2个pc用户,分别用网线连接,如下图
技术图片

  1. 配置LSW1 的优先级以及冗余配置
    [Huawei]sySname SW1
    [SW1]lacp priority 1000
    [SW1]int Eth-Trunk 1
    [SW1-Eth-Trunk1]bpdu enable
    [SW1-Eth-Trunk1]mode lacp-static
    [SW1-Eth-Trunk1]int e0/0/10
    [SW1-Ethernet0/0/10]eth-trunk 1
    [SW1-Ethernet0/0/10]int e0/0/11
    [SW1-Ethernet0/0/11]eth-trunk 1
    [SW1-Ethernet0/0/12]int e0/0/12
    [SW1-Ethernet0/0/12]eth-trunk 1
    [SW1]dis eth-trunk 1                        
    Least Active-linknumber: 1  Max Active-linknumber: 8                          
    Ethernet0/0/10         Unselect 100M     32768   11     289     10100010  1     
    Ethernet0/0/11         Unselect 100M     32768   12     289     10100010  1     
    Ethernet0/0/12         Unselect 100M     32768   13     289     10100010  1 

    配置最大跑的链接数

    [SW1]int Eth-Trunk  1
    [SW1-Eth-Trunk1]max active-linknumber 2
    [SW1-Eth-Trunk1]dis eth-trunk 1                       
    Least Active-linknumber: 1  Max Active-linknumber: 2                          
    ActorPortName          Status   PortType PortPri PortNo PortKey PortState Weight
    Ethernet0/0/10         Unselect 100M     32768   11     289     10100010  1     
    Ethernet0/0/11         Unselect 100M     32768   12     289     10100010  1     
    Ethernet0/0/12         Unselect 100M     32768   13     289     10100010  1
  2. 配置LSW2 ,不需要配置优先级和最大链路数
    [Huawei]sysname SW2
    [SW2]int Eth-Trunk 1
    [SW2-Eth-Trunk1]bpdu enable
    [SW2-Eth-Trunk1]mode lacp-static
    [SW2-Eth-Trunk1]q
    [SW2]int e0/0/10
    [SW2-Ethernet0/0/10]eth-trunk 1
    [SW2]int e0/0/11
    [SW2-Ethernet0/0/11]eth-trunk 1
    [SW2-Ethernet0/0/11]q
    [SW2]int e0/0/12
    [SW2-Ethernet0/0/12]eth-trunk 1
    [SW2-Ethernet0/0/12]q
    [SW2]dis eth-trunk 1                         
    Operate status: up          Number Of Up Port In Trunk: 2                     
    Ethernet0/0/10         Selected 100M     32768   11     289     10111100  1     
    Ethernet0/0/11         Selected 100M     32768   12     289     10111100  1     
    Ethernet0/0/12         Unselect 100M     32768   13     289     10110000  1

    3.配置LSW1, LSW2的网关IP
    配置SW2

    [SW2]int vlanif 1
    [SW2-Vlanif1]ip add 192.168.10.3 24
    [SW2-Vlanif1]dis ip int brief
    Interface                         IP Address/Mask      Physical   Protocol  
    MEth0/0/1                         unassigned           down       down      
    NULL0                             unassigned           up         up(s)     
    Vlanif1                           192.168.10.3/24      up         up

    配置SW1

    [SW1]int vlanif 1
    [SW1-Vlanif1]ip add 192.168.10.2 24
    [SW1-Vlanif1]dis ip int brief
    Interface                         IP Address/Mask      Physical   Protocol  
    MEth0/0/1                         unassigned           down       down      
    NULL0                             unassigned           up         up(s)     
    Vlanif1                           192.168.10.2/24      up         up

    4.配置LSW1的Eth- Trunk2

    [SW1]int Eth-Trunk 2
    [SW1-Eth-Trunk2]trunkport GigabitEthernet 0/0/1 to 0/0/2
    [SW1-Eth-Trunk2]dis eth-trunk 2
    PortName                      Status      Weight 
    GigabitEthernet0/0/1          Up          1      
    GigabitEthernet0/0/2          Up          1  

    5.配置R1

    [Huawei]sysname R1
    [R1]int Eth-Trunk 2
    [R1-Eth-Trunk2]trunkport GigabitEthernet 0/0/0 to 0/0/1
    [R1-Eth-Trunk2]ip add 192.168.10.1 24
    [R1-Eth-Trunk2]display ip int brief
    Interface                         IP Address/Mask      Physical   Protocol  
    Eth-Trunk2                        192.168.10.1/24      up         up   
    [R1-Eth-Trunk2]int Eth-Trunk 1
    [R1-Eth-Trunk1]trunkport GigabitEthernet 0/0/2 to 0/0/3
    [R1-Eth-Trunk1]ip add 12.0.0.1 30
    [R1-Eth-Trunk1]display ip int brief
    Interface                         IP Address/Mask      Physical   Protocol  
    Eth-Trunk1                        12.0.0.1/30         up         up        
    Eth-Trunk2                        192.168.10.1/24      up         up 

    6.配置R2

    [R2]interface Eth-Trunk 5
    [R2-Eth-Trunk5]trunkport g 0/0/2 to 0/0/3
    [R2-Eth-Trunk5]ip add 12.0.0.2 30
    [R2-Eth-Trunk5]dis ip int brief
    Interface                         IP Address/Mask      Physical   Protocol  
    Eth-Trunk5                        12.0.0.2/30          up         up   

    R2需要配置静态路由

    [R2]ip route-static 192.168.10.0 24 12.0.0.1
    [R2]display ip routing-table
       12.0.0.0/30  Direct  0    0           D   12.0.0.2        Eth-Trunk5
       12.0.0.2/32  Direct  0    0           D   127.0.0.1       Eth-Trunk5
      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
    192.168.10.0/24  Static  60   0          RD   12.0.0.1        Eth-Trunk5

    7.PC测试网络
    技术图片
    技术图片
    以上。

链路捆绑实现冗余功能实验

标签:oop   rtp   bpdu   port   image   ddr   路由器   toc   ports   

原文地址:https://blog.51cto.com/14625831/2496800

(0)
(0)
   
举报
评论 一句话评论(0
登录后才能评论!
© 2014 mamicode.com 版权所有  联系我们:gaon5@hotmail.com
迷上了代码!