LTE - Release 10 PUSCH Multiple Codeword Transmit and Receive Modeling

标签：splay   mit   sch   control   info   show   block   als   generate   

Introduction

This example demonstrates the multicodeword transmission and reception in the uplink.

Parameters

% Generate configuration for FRC A3-2
frc = lteRMCUL(‘A3-2‘);

% UE configuration
frc.TotSubframes = 1;   % Total number of subframes
frc.NTxAnts = 2;        % Number of transmit antennas

% Update Physical Uplink Shared Channel (PUSCH) configuration for 2 identically configured codewords
frc.PUSCH.NLayers = 2;
frc.PUSCH.Modulation = repmat({frc.PUSCH.Modulation},1,2);
frc.PUSCH.RV = repmat(frc.PUSCH.RV,1,2);
frc.PUSCH.TrBlkSizes = repmat(frc.PUSCH.TrBlkSizes,2,1);

Encoding

This section sets up the transport blocks and the Uplink Control Information (UCI). This is then coded to generate the Uplink Shared Channel (UL-SCH). The diagram below shows the operations performed internally by lteULSCH.

% Set up the transport block sizes and data for both codewords
TBSs = frc.PUSCH.TrBlkSizes(:,frc.NSubframe+1); % transport block sizes
trBlks = {(randi([0 1], TBSs(1), 1)) (randi([0 1], TBSs(2), 1))}; % data

% Set up UCI contents
CQI = [1 0 1 0 0 0 1 1 1 0 0 0 1 1].‘;
RI  = [0 1 1 0].‘;
ACK = [1 0].‘;

% UL-SCH coding including UCI coding
cws = lteULSCH(frc,frc.PUSCH,trBlks,CQI,RI,ACK);

% PUSCH modulation is applied to the generated codewords
puschSymbols = ltePUSCH(frc,frc.PUSCH,cws);

Decoding

This section demodulates the PUSCH and applies channel decoding. The resulting UCI is then decoded to produce the received Channel Quality Indicator (CQI), Rank Indication (RI) and Acknowledgment (ACK).

% PUSCH demodulation
ulschInfo = lteULSCHInfo(frc,frc.PUSCH,TBSs,length(CQI),length(RI),length(ACK),‘chsconcat‘);    % Get UL-SCH information
llrs = ltePUSCHDecode(frc,ulschInfo,puschSymbols); % Decode PUSCH

% UL-SCH decoding
softBuffer = [];
[rxtrblks,crc,softBuffer] = lteULSCHDecode(frc,ulschInfo,TBSs,llrs,softBuffer);

% UCI decoding
[llrsData,llrsCQI,llrsRI,llrsACK] = lteULSCHDeinterleave(frc,ulschInfo,llrs);
rxCQI = lteCQIDecode(ulschInfo,llrsCQI);    % Decode CQI
rxRI = lteRIDecode(ulschInfo,llrsRI);       % Decode RI
rxACK = lteACKDecode(ulschInfo,llrsACK);    % Decode ACK

esults

The decoded CRC for both codewords is displayed. The transmitted and received CQI, RI and ACK bits are also shown.

CRCs:

Codeword 1: 0
Codeword 2: 0

CQI:
transmitted: 1  0  1  0  0  0  1  1  1  0  0  0  1  1
received   : 1  0  1  0  0  0  1  1  1  0  0  0  1  1

RI:
transmitted: 0  1  1  0
received   : 0  1  1  0

ACK:
transmitted: 1  0
received   : 1  0

LTE - Release 10 PUSCH Multiple Codeword Transmit and Receive Modeling

标签：splay   mit   sch   control   info   show   block   als   generate   

原文地址：https://www.cnblogs.com/zzyzz/p/13288621.html