1.测试拓扑：
2.测试总结：
3.基本配置：
A.路由器R1：
interface Ethernet0/0
ip address 202.100.1.1 255.255.255.0
no shut
B.防火墙SRX:
①配置接口地址：
set interfacesge-0/0/0.0family inetaddress 202.100.1.10/24
set interfacesge-0/0/1.0family inetaddress 10.1.1.10/24
set interfacesge-0/0/2.0family inetaddress 192.168.1.10/24
②将接口划入zone：
setsecurity zones security-zone untrust interfacesge-0/0/0.0
setsecurity zones security-zone trust interfacesge-0/0/1.0
setsecurity zones security-zone dmz interfacesge-0/0/2.0
③配置zone间策略，允许trust到untrust的任何访问：
setsecurity policies from-zone trust to-zone untrust policy Permit-All match source-address any
setsecurity policies from-zone trust to-zone untrust policy Permit-All match destination-address any
setsecurity policies from-zone trust to-zone untrust policy Permit-All match application any
setsecurity policies from-zone trust to-zone untrust policy Permit-All then permit
④配置zone间策略，允许DMZ到untrust的任何访问：
set security policies from-zone dmz to-zoneuntrust policy Permit-All match source-address any
set security policies from-zone dmz to-zoneuntrust policy Permit-All match destination-address any
set security policies from-zone dmz to-zoneuntrust policy Permit-All match application any
set security policies from-zone dmz to-zoneuntrustpolicy Permit-All then permit
C.主机PC1：
IP:10.1.1.8/24
GW:10.1.1.10
D.路由器R2：
interface f0/0
ip address 192.168.1.2 255.255.255.0
no shut
ip route 0.0.0.0 0.0.0.0 192.168.1.10
4.NAT配置：
A.第一种NAT:
Source NAT：Interface NAT配置:
A.指定NAT的zone：
setsecurity nat sourcerule-set Source-NAT from zone trust
setsecurity nat sourcerule-setSource-NATto zone untrust
B.配置Interface NAT:
setsecurity nat source rule-set Source-NAT rule NAT-Interface match source-address 0.0.0.0/0
setsecurity nat source rule-set Source-NAT rule NAT-Interface match destination-address 0.0.0.0/0
setsecurity nat source rule-set Source-NAT rule NAT-Interface then source-nat interface
C.提交配置：
commit
D.验证：
从主机PC1上面ping路由器R1接口地址，并在R1上debug ip icmp，可以看到ICMP源地址为防火墙接口地址
R1#
*Mar 2 01:35:56.797: ICMP: echo reply sent, src 202.100.1.1, dst 202.100.1.10
*Mar 2 01:35:57.793: ICMP: echo reply sent, src 202.100.1.1, dst 202.100.1.10
*Mar 2 01:35:58.809: ICMP: echo reply sent, src 202.100.1.1, dst 202.100.1.10
*Mar 2 01:35:59.749: ICMP: echo reply sent, src 202.100.1.1, dst 202.100.1.10
R1#
B.第二种NAT:
Source NAT：pool based nat配置:
A.配置地址池：
set security nat source pool src-nat-pool1address 202.100.1.11 to 202.100.1.13
B.指定NAT的zone（前面已经配置，可以不配）：
set security nat source rule-set Source-NAT from zone trust
set security nat sourcerule-set Source-NATto zone untrust
C.配置pool based nat：
set security nat source rule-set Source-NAT rule NAT-pool match source-address 0.0.0.0/0
sets ecurity nat source rule-set Source-NAT rule NAT-pool match destination-address 0.0.0.0/0
本文出自 “httpyuntianjxxll.spac..” 博客，请务必保留此出处http://333234.blog.51cto.com/323234/1614744
原文地址：http://333234.blog.51cto.com/323234/1614744
