标签：
2台前端 keepalived+lvs，热备的方式，保证一台lvs前端能正常访问就行，如果一台down，另外一台热备升级到master主机
master: 192.168.1.210 ubuntu 12.0.4
salve: 192.168.1.211 ubuntu 12.0.4
后端2台web服务器通过lvs的算法轮询被访问
web1: 192.168.1.204 centos 5.10 nginx+tomcat
web2: 192.168.1.206 centos 5.10 nginx+tomcat
vip: 192.168.1.207
1：首先 web1和web2都不用装ipvsadm和keepalived，只要启用一个脚本即可，
当然你已经把nginx+tomcat已经配置完，并能正常访问页面
vim realserver.sh |
#!/bin/bash # # Script to start LVS DR real server. # description: LVS DR real server # . /etc/rc.d/init.d/functions VIP=192.168.1.207 #这里根据需要改成自己的VIP地址 host=`/bin/hostname` case "$1" in start) # Start LVS-DR real server on this machine. /sbin/ifconfig lo down /sbin/ifconfig lo up echo 1 > /proc/sys/net/ipv4/conf/lo/arp_ignore echo 2 > /proc/sys/net/ipv4/conf/lo/arp_announce echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce /sbin/ifconfig lo:0 $VIP broadcast $VIP netmask 255.255.255.255 up /sbin/route add -host $VIP dev lo:0 ;; stop) # Stop LVS-DR real server loopback device(s). /sbin/ifconfig lo:0 down echo 0 > /proc/sys/net/ipv4/conf/lo/arp_ignore echo 0 > /proc/sys/net/ipv4/conf/lo/arp_announce echo 0 > /proc/sys/net/ipv4/conf/all/arp_ignore echo 0 > /proc/sys/net/ipv4/conf/all/arp_announce ;; status) # Status of LVS-DR real server. islothere=`/sbin/ifconfig lo:0 | grep $VIP` isrothere=`netstat -rn | grep "lo:0" | grep $VIP` if [ ! "$islothere" -o ! "isrothere" ];then # Either the route or the lo:0 device # not found. echo "LVS-DR real server Stopped." else echo "LVS-DR real server Running." fi ;; *) # Invalid entry. echo "$0: Usage: $0 {start|status|stop}" exit 1 ;; esac |
chmod +x realserver.sh |
./realserver.sh start |
可通过ifconfig和route -n来查询刚才脚本实现的功能
如果可以把此脚本放在启动时运行
ifconfig
route -n
2：然后再master和salve分别安装ipvsadm和keepalived
yum install -y keepalived ipvsadm (centos redhat)
或者
apt-get install keepalived ipvsadm (debian ubuntu)
安装完ipvsadm和keepalived，不用配置lvs，直接用keepalived来启用lvs就行
在master主机设置：
vim /etc/keepalived/keepalived.conf |
global_defs
{
router_id master_210
}
vrrp_instance shengzc {
state MASTER
interface eth0
virtual_router_id 100 #这个数值 master和slave必须统一
priority 151 #这个数值决定哪台服务器是master
advert_int 1
authentication {
auth_type PASS
auth_pass 123456
}
virtual_ipaddress {
192.168.1.207
}
}
virtual_server 192.168.1.207 80 {
delay_loop 6
lb_algo wrr
lb_kind DR
# persistence_timeout 50
protocol TCP
real_server 192.168.1.204 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
real_server 192.168.1.206 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
} |
启动keepalived
/etc/init.d/keepalived start |
在slave主机设置：
vim /etc/keepalived/keepalived.conf |
global_defs
{
router_id slave_211
}
vrrp_instance shengzc {
state MASTER
interface eth0
virtual_router_id 100 #这个数值 master和slave必须统一
priority 150 #这个数值决定哪台服务器是master 这里我们比master数值低，所以角色是backup，
advert_int 1
authentication {
auth_type PASS
auth_pass 123456
}
virtual_ipaddress {
192.168.1.207
}
}
virtual_server 192.168.1.207 80 {
delay_loop 6
lb_algo wrr
lb_kind DR
# persistence_timeout 50
protocol TCP
real_server 192.168.1.204 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
real_server 192.168.1.206 80 {
weight 1
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 80
}
}
} |
启动keepalived
/etc/init.d/keepalived start |
可以运行 ipvsadm -ln 来查看是否启用
ipvsadm
好了，现在我们直接访问 http://192.168.1.207 就实现了，高可用性，高负载的集群
lvs+keepalived+nginx+tomcat高可用高性能集群部署
标签：
原文地址：http://my.oschina.net/liting/blog/384369
