标签：
Main error codes | ||
Error Code | Description | Details and Solution |
80 | Can not initialize bar code reader | Power-cycle the unit and retry the operation |
81 | No response from bar code reader | |
82 | No response from EEPROM on robotic controller | |
83 | Robotic controller generic problem | |
84 | Setting of gripper motor parameters failed NOTE:?Gripper is the part of the robotics assembly that pinches media in order to grip it. | |
85 | Setting of slider motor parameters failed NOTE:?Slider is the part of the robotics assembly that plunges in and out for get and put operations. | |
86 | Setting of elevator motor parameters failed NOTE:?Elevator is the part of the robotics assembly that moves in the vertical direction. | |
87 | Setting of rotation motor parameters failed NOTE:?Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. | |
88 | Setting of sled motor parameters failed NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | |
89 | Gripper obstructed NOTE:?Gripper is the part of the robotics assembly that pinches media in order to grip it. | Run the Wellness Test |
8A | Slider obstructed NOTE:?Slider is the part of the robotics assembly that plunges in and out for get and put operations. | |
8B | Elevator obstructed NOTE:?Elevator is the part of the robotics assembly that moves in the vertical direction. | |
8C | Rotation obstructed NOTE:?Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. | |
8D | Sled obstructed NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | |
8E | Ends of gripper movement not in expected range NOTE:?Gripper is the part of the robotics assembly that pinches media in order to grip it. | |
8F | Ends of slider movement not in expected range NOTE:?Slider is the part of the robotics assembly that plunges in and out for get and put operations. | |
90 | Ends of elevator movement not in expected range NOTE:?Elevator is the part of the robotics assembly that moves in the vertical direction. | |
91 | Ends of rotation movement not in expected range NOTE:?Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. | |
92 | Ends of sled movement not in expected range NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | |
93 | Gripper reached a position beyond expected range NOTE:?Gripper is the part of the robotics assembly that pinches media in order to grip it. | |
94 | Slider reached a position beyond expected range NOTE:?Slider is the part of the robotics assembly that plunges in and out for get and put operations. | |
95 | Elevator reached a position beyond expected range NOTE:?Elevator is the part of the robotics assembly that moves in the vertical direction. | |
96 | Rotation reached a position beyond expected range NOTE:?Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. | |
97 | Sled reached a position beyond expected range NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | |
98 | Cartridge present sensor not found | |
99 | Slider home sensor not found NOTE:?Slider is the part of the robotics assembly that plunges in and out for get and put operations. | |
9A | Rotation home sensor not found NOTE:?Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. | |
9B | Sled position sensor not found NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | |
9C | Gripper range of motion out of specification NOTE:?Gripper is the part of the robotics assembly that pinches media in order to grip it. | |
9D | Slider range of motion out of specification NOTE:?Slider is the part of the robotics assembly that plunges in and out for get and put operations. | |
9E | Elevator range of motion out of specification NOTE:?Elevator is the part of the robotics assembly that moves in the vertical direction. | |
9F | Rotation range of motion out of specification NOTE:?Rotation is the part of the robotics assembly that turns the robot to face each magazine and the drive. | |
A0 | Sled range of motion out of specification NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | |
A1 | Open Mail Slot failed |
|
B0 | Command from library controller to robotics controller didn‘t complete in time allotted |
|
B1 | Robot controller reported format error on command from library controller | |
B2 | Communication to robot from library controller failed | |
B3 | Robot stopped due to a released magazine |
|
B4 | Tape in gripper?sensor did not report the expected value NOTE:?Gripper is the part of the robotics assembly that pinches media in order to grip it. |
|
B5 | Robotic controller not responding to command from library controller |
|
C0 | Network initialization failed | Check network cable,
|
C1 | Telnet interface initialization failed | |
C2 | Web server initialization failed | |
C6 | Ping command did not reach target | |
C7 | Cannot upgrade firmware from USB |
|
D0 | ROM checksum incorrect | Retry firmware upgrade |
D1 | RAM error during Power-On-Self-Test | Power-cycle the unit |
D2 | Read or Write to NVRAM on library controller failed | |
D3 | Time controller failed during Power-On-Self-Test | |
D4 | Internal UART serial communication error | |
D5 | Communication to display failed | |
D6 | Library controller memory error | |
D7 | Fatal system error | |
D8 | Library controller data base error | |
D9 | No SCSI IC detected | |
DA | In?Wellness Test?the bar code read did not match the previous value for that tape |
|
DB | External cooling fan error. sub-code indicates which fan is affected. sub-code 00: drive sled #1, NOTE:?Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. | Check if the fan is operational and not obstructed |
F0 | Drive exceeded temperature specification | Check ambient temperature conditions and fans |
F1 | Library controller lost communication with the drive | Re-seat the tape drive |
F2 | Drive sled5 not present | |
F3 error | Drive hardware |
|
F4 | Time allotted for drive loading exceeded |
|
F5 | Time allotted for drive unloading exceeded |
|
HP StorageWorks MSL2024 Tape Libraries - Tape library Error Codes
标签：
原文地址：http://www.cnblogs.com/IvanChen/p/4493127.html
