Lvs+Keepalived高可用负载均衡配置,近期需要使用，所以自己搞了个虚拟机进行了简单的安装测试，希望可以帮助大家解决小问题。
mater 192.168.78.128 //keepalived+lvs
slave 192.168.78.129 //keepalived+lvs
real server1 192.168.78.130 //web1,nginx
real server2 192.168.78.131 //web1,nginx
vip 192.168.78.132
1.首先给服务器安装依赖包
yum -y install gcc gcc-c++ make pcre pcre-devel kernel-devel openssl-devel
2.安装keepalived，在master和slave上
cd /root/software wget http://www.keepalived.org/software/keepalived-1.2.15.tar.gz tar xzf keepalived-1.2.15.tar.gz cd keepalived-1.2.15 ./configure --prefix=/usr/local/keepalived --with-kernel-dir=/usr/src/kernels/2.6.32-504.16.2.el6.i686/ make make install cp -a /usr/local/keepalived/etc/rc.d/init.d/keepalived /etc/init.d/ cp -a /usr/local/keepalived/etc/sysconfig/keepalived /etc/sysconfig/ mkdir /etc/keepalived cp -a /usr/local/keepalived/etc/keepalived/keepalived.conf /etc/keepalived/ cp -a /usr/local/keepalived/sbin/keepalived /usr/bin/
注意：--with-kernel-dir=/usr/src/kernels/2.6.32-504.16.2.el6.i686/ 这个选项一定要加；这个选项并不是把keepalived编译进内核，而是指定使用内核源码中的头文件，即include目录（只有在配置lvs时才用此选项，其他时候不需要）
3.配置keepalived.conf文件，先将原来的模板配置文件拷贝一份备份，然后在修改
cp /etc/keepalived/keepalived.conf /etc/keepalived/keepalived.conf.old
vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
notification_email {
1015099137@qq.com #故障联系人
}
notification_email_from root@localhost #故障发发送人
smtp_server 127.0.0.1
smtp_connect_timeout 30
router_id lvs
}
vrrp_instance VI_1 {
state MASTER
interface eth0
virtual_router_id 51 #虚拟路由标识，主从相同
priority 150
advert_int 1
authentication {
auth_type PASS
auth_pass 1111 #主从认证密码，必须保持一致
}
virtual_ipaddress {
192.168.78.132 #Web虚拟IP（VTP）
}
}
virtual_server 192.168.78.132 80 { #定义虚拟IP和端口
delay_loop 6 #检查真实服务器时间，单位秒
lb_algo rr #设置负载调度算法
lb_kind DR #设置LVS负载均衡DR模式
persistence_timeout 50 #同一IP的连接50秒内被分配到同一台真实服务器
protocol TCP #使用TCP协议检查realserver状态
real_server 192.168.78.130 80 { #第一个web服务器
weight 3 #节点权重值
TCP_CHECK { #健康检查方式
connect_timeout 10 #连接超时
nb_get_retry 3 #重试次数
delay_before_retry 3 #重试间隔/S
}
}
real_server 192.168.78.131 80 { #第二个web服务器
weight 3
TCP_CHECK {
connect_timeout 10
nb_get_retry 3
delay_before_retry 3
}
}
}在（备）192.168.186.129，对配置文件做如下修改：
将state master改为state backup
将priority 150改为priority 100
/etc/init.d/keepalived start
查看是否启动：
tail -n 30 /var/log/messages
注意：/etc/sysconfig /keepalived 和 /etc/keepalived/keepalived.conf 的路径一定要正确，因为在执行/etc/init.d/keepalived这个启动脚本时，会读取/etc/sysconfig/keepalived 和 /etc/keepalived/keepalived.conf 这两个文件
4.安装IPVS：在master和slave进行如下操作
(1)安装依赖包
yum -y install popt popt-devel libnl libnl-devel popt-static
(2)安装IPVS
cd /root/software wget http://www.linuxvirtualserver.org/software/kernel-2.6/ipvsadm-1.26.tar.gz tar xzf ipvsadm-1.26.tar.gz cd ipvsadm-1.26 make && make insatll ipvsadm --help //查看帮助，如果出现就说明安装成功
5.配置real server (master1,slave1)
注意：每台real server都要进行以下操作：
我们采用的是DR负载方式，用户的请求到达real server后，real server处理完数据后是直接返回给用户的，不再经过LB负载机，因此，需要在每台real server上都绑定一个vip,vip绑定在lo接口
vim /etc/rc.d/init.d/rscreatevip.sh
#!/bin/bash #real server create vip VIP=192.168.78.132 #./etc/rc.d/init.d/functions case $1 in start) echo "real server create vip" /sbin/ifconfig lo:0 $VIP broadcast $VIP netmask 255.255.255.255 up echo 1 > /proc/sys/net/ipv4/conf/lo/arp_ignore echo 2 > /proc/sys/net/ipv4/conf/lo/arp_announce echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore echo 2 > /proc/sys/net/ipv4/conf/all/arp_announce ;; stop) /sbin/ifconfig lo:0 down echo "real server remove vip" echo 0 > /proc/sys/net/ipv4/conf/lo/arp_ignore echo 0 > /proc/sys/net/ipv4/conf/lo/arp_announce echo 0 > /proc/sys/net/ipv4/conf/all/arp_ignore echo 0 > /proc/sys/net/ipv4/conf/all/arp_announce ;; *) echo "usage: (start|stop)" exit 1 esac
chmod 755 /etc/init.d/rscreatevip.sh #加执行权限
/etc/init.d/rscreatevip.sh start
echo "/etc/init.d/rscreatevip.sh start" >> /etc/rc.d/rc.local #设置开机自动启动
6.把real server 2台web开启
/usr/local/nginx/sbin/nginx
/usr/local/php/sbin/php-fpm
echo "welcome to 130" > /data/web/welcome.com/index.html
echo "welcome to 131" > /data/web/welcome.com/index.html
7.把master和slave的keepalived启动，并把所以机器的防火墙和selinux全部关闭进行测试
/etc/init.d/keepalived start
service iptables stop
setenforce 0
8.在master上执行如下命令
ipvsadm -ln #查看监控的real server 有哪些
ipaddr #查看vip绑定在哪台LB
9.测试，keepalived,master和slave直接切换
在master上执行
/etc/init.d/keepalived stop
然后查看master日志和slave日志
10.在浏览器输入192.168.78.132看看web是否自动切换页面
需要多刷新几次，才可能会切换，至此我们的实验已经完成，实现了自动切换的功能。
本文出自 “大花猫博客” 博客，请务必保留此出处http://bighuamao.blog.51cto.com/1995527/1659744
原文地址：http://bighuamao.blog.51cto.com/1995527/1659744
